The Materials Science of Coatings and Substrates Part 2 ppsx
The Materials Science of Coatings and Substrates Part 2 ppsx
... adhesive forces.
42
Electrodeposition
22 .
23 .
24 .
25 .
26 .
27 .
28 .
29 .
30.
31.
32.
K.
Takata, Japanese patents SHO-35 1 826 0 (1960) and SHO-38
20 703 (1963)
AMS -24 19A. "Cadmium-Titanium ...
1
3
114 0.88 1.07
1 .26
2
3
24 1.08 1.05
1. 02
3
72 114 0 .26 0 .28
0.3
1
4 72 24 0 .28
0.30
0.3
1
a. From reference
20 .
Background level was...
The Materials Science of Coatings and Substrates Part 6 ppsx
... (22 )
Figures 12 and 13 show the influence of substrate on elongation of
copper deposited from an acid sulfate solution (23 ). With 304 stainless
steel
as
the substrate, the elongation of the ... structure and spacing (21 ).
The effect
of
the type
of
substrate on the properties of nickel
electrodeposited on as-rolled and on annealed, cube-textured copper...
The Materials Science of Coatings and Substrates Part 1 ppt
... 20 3,OOO -21 8,ooO
190 -22 0
Minimum
16
1501
-1
600 21 8,000 -23 2,000
190 -22 0
Minimum
18
1601-1700 23 2,000 -24 7,000
190 -22 0
Minimum
20
1701-1800 24 7,000 -26
1
,OOO
190 -22 0
Minimum
22
a. ...
190 -22 0
Minimum
8
1101- 120 0 160,000- 174,000
190 -22 0
Minimum
10
120
1-1
300
174,OOO-l89,oOO
190 -22 0
Minimum
12
1301 -1400
1
89,OOO -20 3,OOO 19...
The Materials Science of Coatings and Substrates Part 3 ppt
...
6,900
108
10 1 52
22 ,000
48
7,000
161
15 1 52 22, 000
54
7,800
29 1 27 1 52
22 ,000 318 46,100
538
50
1 52 22, 000 337
48,900
1080
100
1 52
22 ,000
488 70,700
(A)
The
cleaning/plating ...
1100
99
90
68
108
20 24-T351
22 1 24 6
25 1 20 4
5083-0 173
144
-
-
6061 -T6 184
20 3 31
46
7075-T651
25 0 23 9 107 21
3
(A)
The pre-plating cycle con...
The Materials Science of Coatings and Substrates Part 5 pdf
...
0 .2
80
(3)
22 0
(5)
22 0 (5)
0
2. 0 92
(1)
154
(3)
20 0 (5) 2. 2 (0 .2)
4 .2 92
(0)
137 (7) 190
(6)
3.7 (0 .2)
5.7
87
(1)
130
(1 1)
20 0 (7)
6 .2 (0 .2)
7.5
86
(3)
122
(8)
21 0 ...
(2)
130
(8)
20 4
(4)
7.0 (0.3)
9.5
85
(2) 123 (7) 20 5 (5) 7.0 (0 .2)
'
From reference
23 .
Each value
is
the average
of
at least three
measurements...
The Materials Science of Coatings and Substrates Part 7 pptx
...
deterioration of their properties. The rate of the phenomenon depends
largely on the nature of the metals, the attacking gases, and the new
products that may form at the interface between the two ...
cally unstable and converts
to
a
phase with the release
of
hydrogen and
causes a contraction of the lattice and cracking of the deposit. Deposit...
The Materials Science of Coatings and Substrates Part 8 doc
... a much better understanding
of
the science
governing the mechanisms and functions of additives for plating solutions,
much
of
the work has been
of
the "trial and error"
or
Edisonian ...
20 .
21 .
22 .
23 .
24 .
25 .
26 .
J.
A. Thornton, "Influence
of
Apparatus Geometry and Deposition
Conditions on the Structure and Topography
of
T...
The Materials Science of Coatings and Substrates Part 9 docx
...
Bottom
Obverse of Obverse of Obverse of Obverse
of
m
receSS
Qeak
leceSS
24 8
198
1 52
120
20 7
25 4
22 7
150
146
181
24 2
143
103
1 33
1 12
1 02
113
163
146
129
158
129
145
133 ...
21 2
176
163
144
1 02
58
77
84
65
100
128
126
101
82
80
Counting was
left
to
right
on
the top of
the
foil and right
to
left
on
the...
The Materials Science of Coatings and Substrates Part 11 doc
... plates
(27 ). The direction
of
the change as a function
of
thiclaiess depends on the
microthrowing power
of
the solution, and is therefore, specific to
the
type
of
solution used (28 ). ... agents;
3)
the accumulation
of
aging byproducts;
4)
the form of current and the current density used for
deposition;
5)
the degree of agitation; and
6)
the...
The Materials Science of Coatings and Substrates Part 12 pot
...
Stress
28 3
A
general rule of thumb is that tensile stresses in the deposits are
deleterious, and the higher the stress the worse the situation in regards
to
fatigue strength
of
the substrate. ...
18.0
25 .0
40.0
410 59,500
186 27 ,000
91 13 ,20 0
59
8,500
17 2, 500
(a) These data are from reference
22 .
The
plating current density was
323
amp/sq
d...