Plastic Product Material and Process Selection Handbook Part 4 pps
Plastic Product Material and Process Selection Handbook Part 4 pps
... 13-36.5 15-21,5 IZ-15 40 -45 9-15 4. 7 -40 .0 10 -x PSI Flexural strength !0 ~ 8.5-18.5 13-21 11-17 11- 14 9- 14 7.1 -49 .5 PSI ln~act strength O~-od) 0.2 4 0.2-1.0 0,25-0 ,40 0. 24- 0 .40 0.25-6.0 0.25-0.8 ... continuous use above 60C ( 140 F). Chlorination to form CPVC increases its heat 1 04 Plastic Product Material and Process Selection Handbook Diallyl Phthala...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 1 ppsx
... plastic, and area D is solid plastic; and (4) melt model of a single screw (courtesy of Spirex Corp.) 146 147 153 157 157 158 159 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 4. 7 4. 8 4. 9 4. 10 4. 11 ... mold, and (c) semipositive compression mold Example of land locations in a split-wedge mold Schematic of transfer molding 14. 3 14. 4 14. 5 44 2 44 5 44 6 45 4 1...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 5 pps
... melting of plastics follows different phases that effect performances. 48 7 1 56 Plastic Product Material and Process Selection Handbook Plasticator melting operation The major processing ... this book has been that it is not difficult to design and fabricate with plastics 144 Plastic Product Material and Process Selection Handbook etc. The melt flow is...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 9 ppsx
... postformed shapes and cuts with some showing dies continued ol Ill x e- m, Q ', .4 298 Plastic Product Material and Process Selection Handbook better transparency and gloss, and reduced ... containers, there may be 2 64 Plastic Product Material and Process Selection Handbook ratio and to reduce polymerization costs and emissions. The fi...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 11 pps
... 211 2 34 49 .7 2 04 229 80.8 266 281 98 .4 206 207 79.2 193 2 04 80.6 193 2 04 93 .4 2 04 212 110.6 2 94 286 61.2 342 382 76.7 296 316 23.8 261 329 64. 6 679 752 67.5 198 217 79.6 3 24 344 ... Plastic Product Material and Process Selection Handbook QJ C.J O D_ C~ .E E c~ O c- c~ c- QJ C9 ct~ c- c~ c- c.J c- a-J C) N C~ 336 Plast...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 16 ppsx
... Conductivity 41 40 30-36 150{) 1200 10 4 I 2 8 6 5 4 5 P20 30-36 1600 1100 10 4 2 2 9 8 8 4 5 42 0SS 35- ,40 1865 1;050 10 4 6 3 9 4 9 4 2 P5 59-61 1575 45 0 6 6 2 8 8 10 7 9 3 P8 58-60 147 5 42 5 8 6 ... shown that only very rough cavity walls (sandblasted surfaces) add considerably to flow rcsistancc. 48 7 542 Plastic Product Material and Process Selectio...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 3 ppt
... fittings and 84 Plastic Product Material and Process Selection Handbook electrical properties remain relatively constant over a wide range of temperatures and humidity. They resist water, acids, and ... into one product, and so on. 1 88 Plastic Product Material and Process Selection Handbook attacked by such partially halogenated solvents as methyl...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 6 pot
... trial and error method for molding optimization. 1 84 Plastic Product Material and Process Selection Handbook and to improve molded part quality and labor productivity. The Shotscopc process ... certain plastics and applications. An example is excessive residence time for the plastic particularly the engineering materials. Any plastic that 1 74 Plastic...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 7 doc
... mold 4- Injection molding 205 Figure 4~ 7 Molding area diagram processing window concept Figure 4, 8 Molding volume diagram processing window concept 208 Plastic Product Material and Process Selection ... melt. The gas can be applied within specific part sections. 222 Plastic Product Material and Process Selection Handbook used between the plasticator a...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 8 pptx
... Nylon-6,6 1. 14 71.2 24. 3 0.878 510 0 .40 1.50 0.15 Nylon-6,10 1.08 67 .4 25.6 0.927 0 .40 0 .40 0.15 Nylon-6,12 1.07 66.8 25.9 0.935 47 5 0 .40 0 .40 0.20 Nylon-ll 1. 04 64. 9 26.6 0.962 46 0 0 .47 0.30 0.10 ... 65.5 26.2 0. 943 41 0 42 5 0.03 Polystyrene, injection impact 1. 04 64. 9 26.6 0.968 44 0 0.t0 Polysulfone 1.25 77 .4 22.3 0.807 650 680 0.30 0.05 Polyurethane 1.20...
Ngày tải lên: 10/08/2014, 12:21