Plastic Product Material and Process Selection Handbook Part 1 ppsx
Plastic Product Material and Process Selection Handbook Part 1 ppsx
... heat and pressure List of ta b les 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 2 .1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2 .10 2 .11 2 .12 2 .13 2 .14 Examples of major plastic families Thermoplastic ... FALLO) Examples of permeability for plastics Examples of transparent plastics 14 18 20 22 24 32 41 43 46 47 10 2 10 6 11 6 11 7 12 2 12 2 12 3 12 5 12 8...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 9 ppsx
... many different products. It consumes about 10 wt% of all plastics. HDPE accounts for nearly 90wt% of the plastic used. PET 296 Plastic Product Material and Process Selection Handbook ~ ~ _~_-=~.~ ... and down to open or close the gap between the pin and bushing. Figure 6.6 is an example for a rectangular shape. 0.850 1. 750 0.950 1& apos;. 200 1. 500 1. 150 1. 6...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 16 ppsx
... Conductivity 414 0 30-36 15 0{) 12 00 10 4 I 2 8 6 5 4 5 P20 30-36 16 00 11 00 10 4 2 2 9 8 8 4 5 420SS 35-,40 18 65 1; 050 10 4 6 3 9 4 9 4 2 P5 59- 61 1575 450 6 6 2 8 8 10 7 9 3 P8 58-60 14 75 425 8 ... "x~.Ejector Plate Clamp Slot Figure 17 .1 Examples of mold layouts, configurations, and actions 510 Plastic Product Material and Process Selectio...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 3 ppt
... yellow Nylon 1. 09 1. 14 Blue mantle yellow Ethyl cellulose 1. 1 -1. 16 Blue white Polyester 1. 12 -1. 46 Yellow Vinyl chloride 1. 15 -1. 65 (Green) yellow orange Acrylic 1. 18 -1. 19 Blue mantle yellow ... 225- 10 - (per cent) 600 500 500 ASTM D-882 Impact strength 7 ,11 4-6 1- 3 (kg-cm) MD-640 300- TD-680 500 1. 3 11 -15 Tear strength 10 0-400 50-300 (gm/0.0 01...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 4 pps
... Compressive strenglh, 13 -36.5 15 - 21, 5 IZ -15 40-45 9 -15 4.7-40.0 10 -x PSI Flexural strength !0 ~ 8.5 -18 .5 13 - 21 11- 17 11 -14 9 -14 7 .1- 49.5 PSI ln~act strength O~-od) 0.2 4 0.2 -1. 0 0,25-0,40 0.24-0.40 ... 250-500 16 0.250 210 (99) >600 ( 315 ) >600 ( 315 ) (confintttms~ CC) (| 21- 260) (I 21- 26 01 ( 71- 1 21) Heat distortion, °F 14 0 400 1 I5-550 16 5-2...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 5 pps
... heating and/ or cooling. 14 8 Plastic Product Material and Process Selection Handbook disperse a standardized plastic/ color concentrate mix. The computer software collects data during a test run and ... melting of plastics follows different phases that effect performances. 487 1 56 Plastic Product Material and Process Selection Handbook Plasticator mel...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 6 pot
... trial and error method for molding optimization. 18 4 Plastic Product Material and Process Selection Handbook and to improve molded part quality and labor productivity. The Shotscopc process ... software and websites are available that concern safety and plastics. 16 6 -17 2,3 71, 429,456, 460 1 72 Plastic Product Material and Process Selection...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 7 doc
... area diagram processing window concept Figure 4,8 Molding volume diagram processing window concept 208 Plastic Product Material and Process Selection Handbook Another example of a processing ... time now occurs when the product can accept the force of ejection and does not distort (hold time is cooling time). 210 Plastic Product Material and Process Selectio...
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 8 pptx
... extrusion 1 77 76 .1 22.7 0.8 21 380 0.40 1. 70 Cellulose proprionate, injection 1. 22 75.5 22.9 0.828 0.40 2.00 0.25 CTFE 2 .11 13 4.0 13 .1 0.473 0.22 0. 01 FEP 2 .11 13 4.0 12 .9 0.465 600 0.28 <0. 01 lonomer, ... 29.0 1. 050 500 0.54 0.07 Ionomer, injection 0.95 59 .1 29.2 1. 060 0.54 0.20 Nylon-6 1. 13 70.5 24.5 0.886 520 0.40 1. 60 0 .15 Nylon-6,6 1. 14 71....
Ngày tải lên: 10/08/2014, 12:21
Plastic Product Material and Process Selection Handbook Part 10 pptx
... drilling and milling will produce channels, and it is not usually possible to follow the cavity contours so closely (Chapter 17 ). 314 Plastic Product Material and Process Selection Handbook ... is developed frozen in and throughout the wall thiclmess. Orientation on molecular 332 Plastic Product Material and Process Selection Handbook thermoplastics....
Ngày tải lên: 10/08/2014, 12:21