Handbook of Plastics, Elastomers and Composites Part 7 docx

... 68.9 204 22.5 Steel 78 33 Note * 12.5 Electroless nickel – – Note * 12.6 Cast iron 74 74 165 Note * 10.8 Fiberglass 1950 20 177 † 11 .7 13.1 Carbon fiber epoxy (T-300) 1 577 66 177 † 2.8–3.6 Cast ceramic ... 13 Note * 2 .7 3 Low-expansion nickel alloys 81 37 144 Note * 1.4–1 .7 Carbon fiber epoxy pitch 55 172 0 2 27 177 † <1 *Above composite †Limited by resin matrix Composite Materia...

Ngày tải lên: 10/08/2014, 12:21

... resins. (Source: Charles A. Harper, Handbook of Plastics, Elastomers, and Composites, 3d ed., McGraw-Hill, New York, 1996, p. 1.29) Thermosets, Reinforced Plastics, and Composites Downloaded from Digital ... Encyclopedia of Polymer Science and Engineering, John Wiley and Sons, New York, 1990, p. 8 27. 265. Berins, M.L., Plastics Engineering Handbook of the Society...

Ngày tải lên: 10/08/2014, 12:21

... (Source: Charles A. H arper, Handbook of Plastics, Elastomers, and Composites, 3d ed., McGraw-Hill, New York, 1996, p. 2.2) Thermosets, Reinforced Plastics, and Composites Downloaded from Digital ... because of their low cost, wide range of colors, high strength/weight ratio, and, more importantly, because of the introduction of molding equipment capable of injecti...

Ngày tải lên: 10/08/2014, 12:21

... 1. 27 28 3.2 PES 203 84.1 2.6 75 1. 37 16.1 3.5 PET 224 159 9.96 101 1.56 21.3 3.6 PPO (modi- fied) 100 54 2.5 2 67 1.09 15 .7 3.9 PPS 260 138 11 .7 69 1. 67 17. 7 3.1 PSU 174 73 .8 2.5 64 1.24 16 .7 3.5 *NB ... 99 41 2.3 3 47 1.18 15 .7 3.0 CA 68 37. 6 1.26 210 1.30 16 .7 5.5 CAB 69 34 .88 346 1.19 12.8 4.8 PTFE 17. 1 .36 173 2.2 17. 7 2.1 PCTFE 50.9 1.3 1 87 2.12 22.2 2.6 PVDF 9...

Ngày tải lên: 10/08/2014, 12:21

... varies as a function of processing parameters (partic- ularly screw speed and pressure), the thermal and mechanical properties of the polymer, and the design and geometry of the screw. A 600-mm ... possibility of oxidation. Blow molding of PP requires the use of higher melt temperatures and shear, but these conditions tend to accelerate the degradation of PP. Because...

Ngày tải lên: 10/08/2014, 12:21

... subject to the Terms of Use as given at the website. Thermosets, Reinforced Plastics, and Composites 177 Particle size analyzer (PSA). A particle size analyzer is an accurate and automatic development ... for the use or accuracy of information in this chapter, such as property data, processing parameters, and applications. Source: Handbook of Plastics, Elastomers, and...

Ngày tải lên: 10/08/2014, 12:21

... Plas- tics, Elastomers, and Composites, 3d ed., Charles A. Harper, ed., McGraw-Hill, New York, 1996. 13.Edward M. Petrie. Joining of Plastics, Elastomers, and Composites, in Handbook of Plastics, Elastomers, ... Elastomers, in Handbook of Plastics, Elastomers, and Composites, 3d ed., Charles A. Harper, ed., McGraw-Hill, New York, 1996. 11.Joseph F. Meier, Fundame...

Ngày tải lên: 10/08/2014, 12:21

... Peters, ed., Chapman and Hall, London, 1998, p. 76 0. 24. Military Handbook 17 B, Plastics for Aerospace Vehicles Part 1, Notice-1, 1 973 . 25. The Composites Materials Handbook- Mil 17, Technomic Publishing ... data in handbooks and computer material property files as “preliminary” and should verify the necessary constants and failure properties of the composite materials...

Ngày tải lên: 10/08/2014, 12:21

... carbide particles, the focus of this section, is arguably the most important of the newer types of MMCs. The low cost of the aluminum matrix and silicon carbide particle makes these composites of particular ... much as two orders of magnitude or more. This greatly expands the range of products for which injection molded polymers can be used. Source: Handbook of Plastic...

Ngày tải lên: 10/08/2014, 12:21

... that may make adhesive bonding impractical. These are summarized in Table 7. 1. Source: Handbook of Plastics, Elastomers, and Composites Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright ... Lee, Stoffey, and Neville Alkyd-silicone (DC–1 377 ) 6. 47 Autonetics data Alkyd-silicone (DC–1400) 4.45 Autonetics data Alkyd-silicone...

Ngày tải lên: 10/08/2014, 12:21