Handbook of Plastics Technologies Part 9 ppsx

... 0 95 2.0 0 47 TABLE 5.17 Fungus Growth * on Molded Plastics: Effect of UV Degradation *.Trace = barely noticeable, slight = 10–30% of surface, moderate = 30–60% of surface, heavy = 60 90 % of ... Terms of Use as given at the website. PLASTICS ADDITIVES PLASTICS ADDITIVES 5.31 5.3.5.5 Strength. The strength of filled and reinforced plastics, resistance to thermal cy- cling...

Ngày tải lên: 10/08/2014, 12:20

... 199 1, p. 383. 34. J.L. Throne, Technology of Thermoforming, Carl Hanser Verlag, Munich, 199 6, pp. 17– 19. 35. J.L. Throne, Technology of Thermoforming, Carl Hanser Verlag, Munich, 199 6, pp. 19 22. 36. ... Engineering Handbook of the Society of the Plastics Industry, 5th ed., Chapman and Hall, New York, 199 1, p. 593 . 46. M.L. Berins, Plastics Engineering Handbook of the...

Ngày tải lên: 10/08/2014, 12:20

... Intern Med 199 8;158:13 09 1314. 59. Diemer T, Desjardins C. Developmental and genetic disorders in spermatogenesis. Hum Reprod 199 9;Update 5:120–140. 60. Griffin JE, Wilson JD. Disorders of the testes ... eds. Williams Textbook of Endocrinology W.B .Saunders, Philadelphia, 199 2, pp. 799 –852. 61. Kremer H, Martens JW, van Reen M, et al. A limited repertoire of mutations of the lut...

Ngày tải lên: 09/08/2014, 15:20

... narrow. TABLE 9. 5 PC Capacity and Demand by Region 199 9 2000 2001 2002 2003 2004 2005 2010 Capacity U.S. 666 666 666 815 815 865 91 5 10 29 W. Europe 575 575 705 845 845 885 885 95 5 Japan 347 347 347 395 395 ... 347 395 395 395 395 445 Total 1588 1588 1718 2055 2055 2145 2 195 24 29 Demand U.S. 4 09 428 424 441 472 5 09 550 736 W. Europe 400 440 435 453 480 516 555 760 Japan 201 22...

Ngày tải lên: 10/08/2014, 11:22

... C (–40°) C 180-4A; 199 3 180-4A; 199 3 180-4A; 199 3 180-4A; 199 3 kJ/m 2 kJ/m 2 kJ/m 2 kJ/m 2 — 50 36 24 — 46 34 25 — 53 25 20 — 52 32 24 DTUL (0.45 MPa), unannealed 75A; 198 7 ° C 131 130 132 128 DTUL ... 5,362,400, 199 4. 8. T. A. Callaghan, K. Takakuwa, D.R. Paul and A.R. Padwa, Polymer 34, 3 796 , 199 3. TABLE 9. 12 Properties of Direct Compression LGF-PP with Impact Modifier Added O...

Ngày tải lên: 10/08/2014, 11:22

... 25 .9 0.18 NB 0 .91 2.25 LDPE 43 11.6 0.17 NB 0 .92 18 .9 2.3 HDPE 74 38.2 373 0 .95 18 .9 2.3 PMP 23.6 1.10 128 0.83 27.6 PI 42.7 3.7 320 1.43 12.2 4.1 PP 102 35.8 1.6 43 0 .90 25.6 2.2 PUR 68 59. 4 ... @ 60 Hz ABS 99 41 2.3 347 1.18 15.7 3.0 CA 68 37.6 1.26 210 1.30 16.7 5.5 CAB 69 34 .88 346 1. 19 12.8 4.8 PTFE 17.1 .36 173 2.2 17.7 2.1 PCTFE 50 .9 1.3 187 2.12 22.2 2.6 PVDF 90 49....

Ngày tải lên: 10/08/2014, 12:20

... Boston, 198 9, p. 677. 1 89. Modern Plastics Encyclopedia Handbook, McGraw-Hill, New York, 199 4. p. 23. 190 . Modern Plastics Encyclopedia Handbook, McGraw-Hill, New York, 199 4. p. 23. 191 . Modern Plastics, ... Engineering Handbook of the Society of the Plastics Industry, 5th ed., Chapman and Hall, New York, 199 1, p. 63. 59. Berins, M.L., Plastics Engineering Handbo...

Ngày tải lên: 10/08/2014, 12:20

... Engineering Handbook of the Society of the Plastics Industry, 5th ed., Chapman and Hall, New York, 199 1, p. 72. 361. Berins, M.L., Plastics Engineering Handbook of the Society of the Plastics Industry, ... New York, 199 1, p. 57. 3 39. Berins, M.L., Plastics Engineering Handbook of the Society of the Plastics Industry, 5th ed., Chapman and Hall, New York, 199 1, p...

Ngày tải lên: 10/08/2014, 12:20

... into the center of the ring permits them to stack layers of phthalocya- nine rings around a siloxane center. This family of polymers offers a number of possibilities in terms of adhesion, heat ... 3.1 .9 Cross-Linking of Elastomers, Coatings, and Adhesives Cross-linking is used not only in thermoset plastics but also in the related fields of elas- tomers, coatings, and adhesi...

Ngày tải lên: 10/08/2014, 12:20

... oil can be 100, 200, or more parts per 100 parts of rubber (phr). Properties of Ethylene-Propylene Rubbers. Elastic properties of EPR or EPDM are better than those of many synthetic rubbers, but ... gas permeability, offer better ozone and weather resistance, and are faster curing than those of CIIR or IIR. The properties of CIIR are between those of BIIR and IIR. Uses of Chlo...

Ngày tải lên: 10/08/2014, 12:20