Foseco Non-Ferrous Foundryman’s Handbook Part 5 doc

... After LM13 250 5 0.27 0.18 (Al–Si12Cu1Mg1) LM 25 250 6 0.40 0.13 (Al–Si7Mg0 .5) LM28 250 10 0.28 0.18 (Al–Si8Cu1 .5 Mg1Ni1) L99 220 7 0. 25 0.12 (Al–Si7 Mg0.3) L 155 90 15 0.24 0.12 (Al–Cu4Si1) 86 Foseco Non-Ferrous ... A B C 68 Foseco Non-Ferrous Foundryman’s Handbook Figure 5. 3 Dimensions of INSURAL ATL one piece ladle liners (Table 5. 3). Figure 5. 4 Temperature loss...

Ngày tải lên: 10/08/2014, 11:22

... inoculation required. 4 .5 31.0 155 0 10.0 1000 86 164 grey 13 .50 5. 0 32.0 no 153 0 8.0 600 129 grey 12 .5 5.0 33.0 no 155 0 4.0 750 243 grey 16.0 x 5. 0 36.0 no 1470 8.0 1 750 250 178 grey 17.80 x 5. 0 36.0 no 150 0 2.0 ... 42 22 54 14.8 12.6 59 50 53 330 3300 109 43 22 60 18.3 15. 6 7360 57 410 4100 1 35 43 22 66 22.1 18.8 8900 60 50 0 50 00 1 65 44 22 72 26 .5 22 .5 10 650...

Ngày tải lên: 10/08/2014, 11:22

... (N/mm 2 ) EN-GJMB-300-6 12 or 15 300 6 – 150 max EN-GJMB- 350 -10 12 or 15 350 10 200 150 max EN-GJMB- 450 -6 12 or 15 450 6 270 150 –200 EN-GJMB -50 0 -5 12 or 15 500 5 300 1 65 2 15 EN-GJMB -55 0-4 12 or 15 550 4 340 180–230 EN-GJMB-600-3 ... 59 22-1981 Blackheart B30-06 12 or 15 300 6 B32-12 12 or 15 320 12 190 150 max B 35- 10 12 or 15 350 10 200 Pearlitic P 45- 06 12 or 15...

Ngày tải lên: 10/08/2014, 11:22

... 0. 25 0 .55 0. 65 Si 0.20 0.60 – 0.60 – 0.60 – 0. 75 – 0. 75 Mn 0 .50 1.00 0 .50 0.80 0.40 0.70 0.30 0.70 0 .50 1.00 P – 0. 05 – 0. 05 – 0. 05 – 0.04 – 0.06 S – 0. 05 – 0. 05 – 0. 05 – 0.04 – 0.06 Cr – 0. 25 ... 7.86 59 .5 13.2 100 482 12.19 57 .8 19.0 200 52 3 12.99 53 .2 26.3 400 59 5 13.91 45. 6 45. 8 600 741 14.68 36.8 73.4 800 960 14.79 28 .5 108.1 1000 13.49 27.6 116 ....

Ngày tải lên: 10/08/2014, 11:22

... 12 Boiling point (°C) 65. 2 78 .5 82.3 Vapour pressure 94 43 32 at 20°C mm Hg Explosion limit (Vol. %) 5. 5–26 .5 3 .5 15 2.0–12 MAK value (ppm) 200 1000 400 Smell limit (ppm) 2000 350 100 The use of water ... conventional coating. % Water remaining 100 90 80 70 60 50 40 30 20 10 0 45 40 35 30 25 20 15 10 5 0 Drying time in minutes 0 10 20 30 40 50 Time (minutes) Rheotec RDT...

Ngày tải lên: 10/08/2014, 11:22

... kg/sec 50 × 50 × 20 35 2 .5 53 2 .5 46 3.1 68 3.1 55 × 55 × 25 45 3.0 68 3.0 59 3.8 88 3.8 75 × 75 × 25 85 5.6 128 5. 6 111 7.0 166 7.0 100 × l00 × 25 150 10.0 2 25 10.0 1 95 12 .5 293 12 .5 1 25 × 1 25 × ... × 30 2 35 15. 6 353 15. 6 306 19 .5 458 19 .5 150 × 150 × 30 340 22 .5 510 22 .5 442 28.1 663 28.1 50 dia. × 25 30 2.0 45 2.0 39 2 .5 59 2 .5 60 dia. × 2...

Ngày tải lên: 10/08/2014, 11:22

... 1180 0 50 0 0.3 600 180 355 1.9 4 25 808 250 17.2 300 51 60 212 25. 3 212 53 64 180 16.7 212 354 0 150 19.2 150 2880 1 25 10.6 150 159 0 90 6 .5 106 689 63 1.4 75 1 05 ≤63 0 .5 38 19 Total 99.6 – 20 3 35 Average ... 172 Fe 78 10.1 5. 5 7.87 12.1 66 Pb 35 20.6 3.4 11.68 29 5. 5 Li 76 9.3 1 .5 0 .53 56 – Mg 156 4.2 4.2 1.74 26 25 Mn 7.8 160 – 7.4 23 – Hg 8.7 96 3. 75 13 .55...

Ngày tải lên: 10/08/2014, 11:22

... kg KC5 350 293 250 363 30 kg KC7910 300 250 450 40 kg KC6294 3 75 260 351 40 kg KC5164 297 217 4 95 45 kg ATL50 KC7 156 470 4 05 462 90 kg ATL100 KC5434 4 75 418 56 0 130 kg ATL 150 KC7804 57 0 54 0 50 0 170 kg ... ATL200 KC7764 57 4 54 0 700 270 kg ATL300 KC7986 730 680 7 25 370 kg ATL400 KC7988 750 680 9 75 570 kg ATL600 KC7990 910 840 850 770 kg ATL800 KC7922 920 840 1000 950...

Ngày tải lên: 10/08/2014, 11:22

... 200– 250 150 –170 0 .5 3.0 65 85 420–600 Grav. die F 160–220 110–130 2 55 5–70 T4 240–280 120–160 6–10 55 –60 T6 240–300 150 –190 2–760–90 Sand F 160–220 90–120 2 55 0– 65 T4 240–280 110–140 6–12 55 –70 T6 ... 190–230 120– 150 4– 855 –70 4 45 630 Sand F 180–240 80–110 8–12 50 – 65 T4 190– 250 90–110 8– 15 50– 65 AM50HP Press. die 180–220 110–140 5 950 –70 440–6 25 AM20HP Press. die...

Ngày tải lên: 10/08/2014, 11:22

... hardness grades of grey iron (EN 156 1:1997) Grade EN-GJL- HB 155 HB1 75 HB1 95 HB2 15 HB2 35 HB 255 HB30 min – 100 120 1 45 1 65 1 85 max 155 1 75 1 95 2 15 2 35 255 Note: Consult EN 156 1:1997 for details. Figure ... 1180 0 50 0 0.3 600 180 355 1.9 4 25 808 250 17.2 300 51 60 212 25. 3 212 53 64 180 16.7 212 354 0 150 19.2 150 2880 1 25 10.6 150 159 0 90 6 .5 106 689 6...

Ngày tải lên: 10/08/2014, 11:22