Engineered Interfaces in Fiber Reinforced Composites Part 15 pptx

Ngày tải lên: 10/08/2014, 11:22

... 40 Engineered interfaces in fiber reinforced composites Kim, J.K. and Mai, Y.W. (1993). Interfaces in composites. In Structure and Properties of Fiber Composites, Materials ... (e.g. AES and XPS), but in terms of quantitative use, SIMS still lags behind the other two 38 Engineered interfaces in fiber reinforced composites Table 2.7 Interlaminar...

Ngày tải lên: 10/08/2014, 11:22

... between Fiber Pull-out and Fiber Push-out Cyclic Loading in Fiber Pull-out and Fiber Push-out Introduction 156 101 131 152 154 156 10 Engineered interfaces in fiber reinforced composites ... following forming of a new compound(s), particularly in MMCs; (f) by mechanical interlocking. After Hull (1981) and Naslain (1993). 2 Engineered interfaces...

Ngày tải lên: 10/08/2014, 11:22

... designated in ASTM D 2344 (1989) involves loading a beam fabricated from unidirectional laminate composites in three-point bending as 56 Engineered interfaces in fiber reinforced composites ... material without fibers) the fibers have a negative reinforcing effect. In the case of a weak interfacial bond, the lower-bound 64 Engineered interfaces in jiber...

Ngày tải lên: 10/08/2014, 11:22

... of debond initiation in the micromechanics model than in the FE model of single fiber composites. All these 144 Engineered interfaces in fiber reinforced composites @+ 1) sinh[&(L-z)] ... showing the criterion for debonding initiation at embedded fiber end or loaded fiber end. 156 Engineered interfaces in jiber reinforced composites "0...

Ngày tải lên: 10/08/2014, 11:22

... drying conditions and homogeneity, the topology and the chemical 178 Engineered interfaces in fiber reinforced composites indication of interpenetration was also observed at the y-aminopropyl-triethoxysi- ... 0.38-0.5 345-520 15. 7 1850-2790 -1.2 12 166 Engineered interfaces in jber reinforced composites Hsueh C.H. and Becher, P.F. (1993). Some consideration...

Ngày tải lên: 10/08/2014, 11:22

... & 5 248 Engineered interfaces in fiber reinforced composites possible to mold into very complex shapes using techniques, such as injection molding, sheet molding, dough molding, etc. at ... (1972) and Hing and Groves (1972). 236 Engineered interfaces in fiber reinforced composites Strife, J., Prewo, K.M. (1982). Silicon carbide fiber- reinforced res...

Ngày tải lên: 10/08/2014, 11:22

... Engineered interfaces in fiber reinforced composites of the composites. For polymer matrix composites (PMCs), the fiber coatings should be able to promote such toughening mechanisms as interfacial ... Polym. Composites 4, 26. 669-675. reinforced thermoplastics. Composites 10, 11 1-1 19. Sci. 33, 85-167. J. Mater. Sci. 21, 1491 -150 1. 268 Engineered...

Ngày tải lên: 10/08/2014, 11:22

... (1992). 300 Engineered interfaces in fiber reinforced composites Finite element analysis has been a popular tool for examining the mechanical response of coated fiber composites (Fan ... terminated butadiene acrylonitrile (CTBN) copolymer for carbon fiber- epoxy matrix system (Gerard, 1988); rubber coating for glass fiber- 294 Engineered interfaces in fiber...

Ngày tải lên: 10/08/2014, 11:22

... Chou et al. (1986). 364 Engineered interfaces in $her reinforced composites McGarry, F.J. (1969). The fracture of polymers and fiber reinforced polymer composites. In Proc. AIAA/ ASME ... control - A review. Composites Sci. Technol. 41, 333-378. resin matrices. Composites Sci. Technol. 43, 283-297. 348 Engineered interfaces in fiber reinforced...

Ngày tải lên: 10/08/2014, 11:22