Engineered Interfaces in Fiber Reinforced Composites Part 14 ppsx

... boron fiber 214, 282 boron fiber reinforced epoxy matrix boron fiber- titanium matrix system 14 braiding 351 brittle interphase 179 brittle matrix 247 buckling 75 bulk laminate 43 bundle fiber ... 330 fiber- avoidance mode 248 fiber bridging 81, 240, 316, 333, 337-338 fiber buckling 200 fiber bundle push-out test 150 fiber/ coating interface 303 fiber coating 279...

Ngày tải lên: 10/08/2014, 11:22

... 43, 147 -1 58. 149 -1 68. control - A review. Composites Sci. Technol. 41, 333-378. resin matrices. Composites Sci. Technol. 43, 283-297. 348 Engineered interfaces in fiber reinforced ... Chou et al. (1986). 364 Engineered interfaces in $her reinforced composites McGarry, F.J. (1969). The fracture of polymers and fiber reinforced polymer composit...

Ngày tải lên: 10/08/2014, 11:22

... between Fiber Pull-out and Fiber Push-out Cyclic Loading in Fiber Pull-out and Fiber Push-out Introduction 156 101 131 152 154 156 10 Engineered interfaces in fiber reinforced composites ... following forming of a new compound(s), particularly in MMCs; (f) by mechanical interlocking. After Hull (1981) and Naslain (1993). 2 Engineered interfaces...

Ngày tải lên: 10/08/2014, 11:22

... 40 Engineered interfaces in fiber reinforced composites Kim, J.K. and Mai, Y.W. (1993). Interfaces in composites. In Structure and Properties of Fiber Composites, Materials ... further, leading to a decrease in ysv . 14 Engineered interjaces in fiber reinforced composites reinforcements like glass, silica, and alumina, but are less effective with alk...

Ngày tải lên: 10/08/2014, 11:22

... designated in ASTM D 2344 (1989) involves loading a beam fabricated from unidirectional laminate composites in three-point bending as 56 Engineered interfaces in fiber reinforced composites ... material without fibers) the fibers have a negative reinforcing effect. In the case of a weak interfacial bond, the lower-bound 64 Engineered interfaces in jiber...

Ngày tải lên: 10/08/2014, 11:22

... of debond initiation in the micromechanics model than in the FE model of single fiber composites. All these 144 Engineered interfaces in fiber reinforced composites @+ 1) sinh[&(L-z)] ... Engineered interfaces in fiber reinforced composites (a) (b) Fig. 4.41. Schematic drawings of loading and unloading processes measuring the relative displacem...

Ngày tải lên: 10/08/2014, 11:22

... drying conditions and homogeneity, the topology and the chemical 178 Engineered interfaces in fiber reinforced composites indication of interpenetration was also observed at the y-aminopropyl-triethoxysi- ... 166 Engineered interfaces in jber reinforced composites Hsueh C.H. and Becher, P.F. (1993). Some consideration of two-way debonding during fiber pull-out....

Ngày tải lên: 10/08/2014, 11:22

... & 5 248 Engineered interfaces in fiber reinforced composites possible to mold into very complex shapes using techniques, such as injection molding, sheet molding, dough molding, etc. at ... (1972) and Hing and Groves (1972). 236 Engineered interfaces in fiber reinforced composites Strife, J., Prewo, K.M. (1982). Silicon carbide fiber- reinforced res...

Ngày tải lên: 10/08/2014, 11:22

... Polym. Composites 4, 26. 669-675. reinforced thermoplastics. Composites 10, 11 1-1 19. Sci. 33, 85-167. J. Mater. Sci. 21, 149 1-1501. 268 Engineered interfaces in fiber reinforced ... to Fig. 6 .14 258 Engineered interfaces in fiber reinforced composites interface Fig. 6.13. The Cook-Gordon (1964) mechanisms: tensile debonding occurs at...

Ngày tải lên: 10/08/2014, 11:22

... terminated butadiene acrylonitrile (CTBN) copolymer for carbon fiber- epoxy matrix system (Gerard, 1988); rubber coating for glass fiber- 294 Engineered interfaces in fiber reinforced composites ... carbon fiber- epoxy matrix compositesa. Carbon-epox y 230 0.2 3.0 0.4 37.7 1.25 -9.97 aAfter Kim et al. (1992). 300 Engineered interfaces in fiber reinforce...

Ngày tải lên: 10/08/2014, 11:22