Engineered Interfaces in Fiber Reinforced Composites Part 13 ppsx

... Chou et al. (1986). 364 Engineered interfaces in $her reinforced composites McGarry, F.J. (1969). The fracture of polymers and fiber reinforced polymer composites. In Proc. AIAA/ ASME ... strands, instead of interfacial debonding, resulting in. limited Local waviness in in-plane yarn created b through-the-thrckness reinforcement Resin pocket around through-...

Ngày tải lên: 10/08/2014, 11:22

... 337-338 fiber buckling 200 fiber bundle push-out test 150 fiber/ coating interface 303 fiber coating 279-282, 293, 301 fiber damage 355 fiber diameter 254 fiber fracture criterion 124 fiber ... interlaminar fracture test interlaminar shear strength intermediate modulus interfacial phenomena in composite materials Interpenetrating network interfacial shear stress ion sc...

Ngày tải lên: 10/08/2014, 11:22

... between Fiber Pull-out and Fiber Push-out Cyclic Loading in Fiber Pull-out and Fiber Push-out Introduction 156 101 131 152 154 156 10 Engineered interfaces in fiber reinforced composites ... following forming of a new compound(s), particularly in MMCs; (f) by mechanical interlocking. After Hull (1981) and Naslain (1993). 2 Engineered interfaces...

Ngày tải lên: 10/08/2014, 11:22

... 40 Engineered interfaces in fiber reinforced composites Kim, J.K. and Mai, Y.W. (1993). Interfaces in composites. In Structure and Properties of Fiber Composites, Materials ... (e.g. AES and XPS), but in terms of quantitative use, SIMS still lags behind the other two 38 Engineered interfaces in fiber reinforced composites Table 2.7 Interlaminar...

Ngày tải lên: 10/08/2014, 11:22

... designated in ASTM D 2344 (1989) involves loading a beam fabricated from unidirectional laminate composites in three-point bending as 56 Engineered interfaces in fiber reinforced composites ... material without fibers) the fibers have a negative reinforcing effect. In the case of a weak interfacial bond, the lower-bound 64 Engineered interfaces in jiber...

Ngày tải lên: 10/08/2014, 11:22

... of debond initiation in the micromechanics model than in the FE model of single fiber composites. All these 144 Engineered interfaces in fiber reinforced composites @+ 1) sinh[&(L-z)] ... the two loading geometry arise mainly from the Poisson effects at the debonded interface, which are distinct in each loading. 136 Engineered interfaces in jiber rei...

Ngày tải lên: 10/08/2014, 11:22

... drying conditions and homogeneity, the topology and the chemical 178 Engineered interfaces in fiber reinforced composites indication of interpenetration was also observed at the y-aminopropyl-triethoxysi- ... 2791-2800. 168 Engineered interfaces in fiber reinforced composites Nairn, J.A. (1992). Variational mechanics analysis of the stresses around breaks in...

Ngày tải lên: 10/08/2014, 11:22

... & 5 248 Engineered interfaces in fiber reinforced composites possible to mold into very complex shapes using techniques, such as injection molding, sheet molding, dough molding, etc. at ... (1972) and Hing and Groves (1972). 236 Engineered interfaces in fiber reinforced composites Strife, J., Prewo, K.M. (1982). Silicon carbide fiber- reinforced res...

Ngày tải lên: 10/08/2014, 11:22

... Engineered interfaces in fiber reinforced composites of the composites. For polymer matrix composites (PMCs), the fiber coatings should be able to promote such toughening mechanisms as interfacial ... Fig. 6.14 258 Engineered interfaces in fiber reinforced composites interface Fig. 6 .13. The Cook-Gordon (1964) mechanisms: tensile debonding occurs at the...

Ngày tải lên: 10/08/2014, 11:22

... terminated butadiene acrylonitrile (CTBN) copolymer for carbon fiber- epoxy matrix system (Gerard, 1988); rubber coating for glass fiber- 294 Engineered interfaces in fiber reinforced composites ... carbon fiber- epoxy matrix compositesa. Carbon-epox y 230 0.2 3.0 0.4 37.7 1.25 -9.97 aAfter Kim et al. (1992). 300 Engineered interfaces in fiber reinforce...

Ngày tải lên: 10/08/2014, 11:22