Handbook of Plastics Technologies Part 6 docx

... Padwa, Polymer 34, 37 96, 1993. TABLE 9.12 Properties of Direct Compression LGF-PP with Impact Modifier Added On-Line (WO 2004/035295) 1234 Composition PP 67 65 63 61 POE 02 46 Glass 30 30 30 30 Color ... 1.04 Coefficient of linear thermal expansion (cm/cm, °C) D -69 6 7.6E-05 9.3E-05 9.3E-05 8.8E-05 Notched Izod impact strength (23°C, J/m) D-2 56 160 310 553 203 Flexural modulus...

Ngày tải lên: 10/08/2014, 11:22

... modifi- cation of the letter symbols permitted. PET can be used instead of PETE, PE-HD instead of HDPE, PVC instead of V, PE-LD instead of LDPE, and O in place of Other. 60 ISO 11 469 :2000, Plastics Generic ... collection and processing of the materials. Collection of plastics for recycling often occurs as part of a system designed to collect a variety of materials,...

Ngày tải lên: 10/08/2014, 12:20

... PC Capacity and Demand by Region 1999 2000 2001 2002 2003 2004 2005 2010 Capacity U.S. 66 6 66 6 66 6 815 815 865 915 1029 W. Europe 575 575 705 845 845 885 885 955 Japan 347 347 347 395 395 395 395 ... here. 9.2.2 Thermoplastics Let us first review various thermoplastics used in automotive applications. These include nylon 6, 6-based blends (e.g., nylon 6, 6-PPO), glass-filled nylon 6, 6...

Ngày tải lên: 10/08/2014, 11:22

... constant @ 60 Hz ABS 99 41 2.3 347 1.18 15.7 3.0 CA 68 37 .6 1. 26 210 1.30 16. 7 5.5 CAB 69 34 .88 3 46 1.19 12.8 4.8 PTFE 17.1 . 36 173 2.2 17.7 2.1 PCTFE 50.9 1.3 187 2.12 22.2 2 .6 PVDF 90 49.2 ... 2.25 LDPE 43 11 .6 0.17 NB 0.92 18.9 2.3 HDPE 74 38.2 373 0.95 18.9 2.3 PMP 23 .6 1.10 128 0.83 27 .6 PI 42.7 3.7 320 1.43 12.2 4.1 PP 102 35.8 1 .6 43 0.90 25 .6 2.2 PUR 68 59.4...

Ngày tải lên: 10/08/2014, 12:20

... 1.45 1.41 1.29–1.40 1.55–1.70 1.27 1.23 HDT, °C 264 psi 66 psi 50–85 115–190 1 96 225 2 16 260 260 > 260 221 268 21 65 75 210–227 243–249 64 70 65 74 Downloaded from Digital Engineering Library ... 220– 267 220– 267 – 285 212– 265 245– 265 – – Tensile modulus, MPa 1,930–3,000 8, 960 –10,000 – – 2, 760 –4,140 8, 960 –9,930 – – Ultimate tensile strength, MPa 56 60 96 134 124–134...

Ngày tải lên: 10/08/2014, 12:20

... Oxford, 1995, p. 260 . 165 . Berins, M.L., Plastics Engineering Handbook of the Society of the Plastics Industry, 5th ed., Chapman and Hall, New York, 1991, p. 55. 166 . 166 166 Kroschwitz, J.I., ... M.L., Plastics Engineering Handbook of the Society of the Plastics Industry, 5th ed., Chapman and Hall, New York, 1991, p. 63 . 60 . Berins, M.L., Plastics Engineering...

Ngày tải lên: 10/08/2014, 12:20

... 160 . 366 . Berins, M.L., Plastics Engineering Handbook of the Society of the Plastics Industry, Inc., 5th ed., Chapman and Hall, New York, 1991, p. 72. 367 . Berins, M.L., Plastics Engineering Handbook ... M.L., Plastics Engineering Handbook of the Society of the Plastics Industry, 5th ed., Chapman and Hall, New York, 1991, p. 72. 360 . Berins, M.L., Plastics Eng...

Ngày tải lên: 10/08/2014, 12:20

... polymerization of bis- FIGURE 3 .65 Copolymerization of isocyanate and epoxy to polyoxazolidone. FIGURE 3 .66 Hexaazatriphenylene trianhy- dride. FIGURE 3 .67 Cyclic tetramerization of phthalonitrile ... into the center of the ring permits them to stack layers of phthalocya- nine rings around a siloxane center. This family of polymers offers a number of possibilities in terms o...

Ngày tải lên: 10/08/2014, 12:20

... oil. The amount of oil can be 100, 200, or more parts per 100 parts of rubber (phr). Properties of Ethylene-Propylene Rubbers. Elastic properties of EPR or EPDM are better than those of many synthetic ... is subject to the Terms of Use as given at the website. ELASTOMERS ELASTOMERS 4 .65 Properties of Halobutyl Rubbers. Properties of vulcanizates are enhanced over those of...

Ngày tải lên: 10/08/2014, 12:20

... 0.94–1.00 1.10–1.40 1.10–1.30 1.00–1.20 Shore hardness 20A 60 D 60 A 65 D 35A–50D 35D–72D 60 A–55D~ 60 A 65 D Low-temperature limit, °C –70 60 60 65 –50 –40 High-temperature limit, °C 70–100 70–100 135 ... compounded for a specific use. Comparison of Properties. Properties of examples of the above TPEs are given in Table 4. 16. 4 .6. 4 Processing of TPEs 4 .6. 4.1 Need for Drying T...

Ngày tải lên: 10/08/2014, 12:20