LEGO MINDSTORMS - Robotics Invention System-2 Projects part 12 pot

LEGO MINDSTORMS - Robotics Invention System-2 Projects part 12 pot

LEGO MINDSTORMS - Robotics Invention System-2 Projects part 12 pot

... the transmission. Slide the half-length bushing onto the axle, leaving one-and-a-half studs of axle exposed on the near side of the bushing. Final Step 1 Place the 12t bevel gear on the short stub ... snugly between the two half- length bushings. Arm Pivot Step 2 Leave a one- stud gap between the 24t crown gear and the first six-stud TECHNIC beam. Arm Pivot Step 3 The three- quarter-length pi...
Ngày tải lên : 10/08/2014, 04:22
  • 25
  • 215
  • 0
LEGO MINDSTORMS - Robotics Invention System-2 Projects Part 3 ppt

LEGO MINDSTORMS - Robotics Invention System-2 Projects Part 3 ppt

... Techno-Walker 42 Assembling the Body Now you will put the entire body together and brace the components so that they are stable. Get out the sub-assembly for the top of the body. Attach the sub- assembly ... Chicken Techno-Walker 60 Putting It All Together You now have a body with walking legs and a head. It’s time to finish your creation. Connect the body and legs sub-assembly to the head su...
Ngày tải lên : 10/08/2014, 04:22
  • 25
  • 348
  • 0
LEGO MINDSTORMS - Robotics Invention System-2 Projects part 4 potx

LEGO MINDSTORMS - Robotics Invention System-2 Projects part 4 potx

... system employed every- where from Earth to the outer reaches of the Alpha Centauri system. Its ability to mark targets in all directions is its most valued asset. This is a LEGO model of a standard ... onto the axle and then insert the half- pins into the gear. The pins should make a 2x4 rectangular pattern. Turntable Step 9 Attach the 2x4 brick onto the half-pins on the 40t gear. 230_RIS_0...
Ngày tải lên : 10/08/2014, 04:22
  • 25
  • 266
  • 0
LEGO MINDSTORMS - Robotics Invention System-2 Projects part 5 docx

LEGO MINDSTORMS - Robotics Invention System-2 Projects part 5 docx

... the brick from Full Turret Step 37 using the 1x12 TECHNIC brick. 230_RIS_03.qxd 10/9/02 8:46 AM Page 108 Robot 3 • Missile Turret 94 Full Turret Step 12 Attach the bushings. Full Turret Step 13 Attach ... we want to elevate the turret a little bit so we use a liftarm to create a non-perpendicular angle. Attach all the parts as shown. 230_RIS_03.qxd 10/9/02 8:46 AM Page 107 Robot 3 • Missile...
Ngày tải lên : 10/08/2014, 04:22
  • 25
  • 322
  • 0
LEGO MINDSTORMS - Robotics Invention System-2 Projects part 7 doc

LEGO MINDSTORMS - Robotics Invention System-2 Projects part 7 doc

... 4 • MINDSTORMS F1 Racer 147 Bumper Step 12 Attach four half-length pins to the liftarms. Bumper Step 13 Seat the 1x2 bricks on top of the half-length pins. Don’t forget to insert the half-length ... arms or other parts with holes. It connects parts at perpendicular angles so it is good for bracing in certain situations, too. 230_RIS_04.qxd 10/9/02 5:56 PM Page 147 Robot 4 • MINDSTORMS...
Ngày tải lên : 10/08/2014, 04:22
  • 25
  • 233
  • 0
LEGO MINDSTORMS - Robotics Invention System-2 Projects part 9 docx

LEGO MINDSTORMS - Robotics Invention System-2 Projects part 9 docx

... open the Safe can be re-programmed at any time. Robot 8 205 The ULK (Useful LEGO Knowledge) Robot 8 • The ULK (Useful LEGO Knowledge) 209 Bricks & Chips… LEGO Connections LEGO connections are ... FetchBot (http://ozbricks.com/benw /lego/ fetchbot/index.html). Jonathan modified Ben’s three motor design so it could be built using only the parts in the Robotics Invention System...
Ngày tải lên : 10/08/2014, 04:22
  • 25
  • 256
  • 0