Recent Advances in Mechatronics - Ryszard Jabonski et al (Eds) Episode 1 Part 10 ppt

... quickly for micro-channels of bigger cross-sections 10 -1 mm 2 , whereas mi- cro-channels of very small cross-sections at the range of 10 -3 mm 2 are al- most not filled at all. It can also be seen ... 45 The quality of grinidng wheel: 500P Grinding wheel NC / Grinding wheel C Grinding wheel K45 / Grinding wheel C Grinding wheel K90 / Grinding wheel C Fig. 1. The influence...

Ngày tải lên: 10/08/2014, 02:20

... Reasoning 15 (19 96) 2 5-4 7. [3] S. W. Leung, J. W. Minett “The Use of Fuzzy Spaces in Signal Detection”, Fuzzy Sets and Systems 11 4 (2000) 17 5 -1 84. [4] M. Marseguerra, E. Zio, P. Baraldi, A. ... “Fault Detection for Nonlinear Systems with Uncertain Parameters Based on the Interval Fuzzy Model”, Engineering Ap- plications of Artificial Intelligence 20 (2007) 50 3-5 10 ....

Ngày tải lên: 10/08/2014, 02:20

... 9 10 11 12 13 14 15 time [s] score bbc3 cact mobl susi Fig.2. The average score given in time to 4 sequences across the whole bitrate range 1 Quantifying the amount of spatial and temporal information ... scene cut (fig. 3). Although it may cause some problems with coding, observers seem not to react to this incident at all (fig. 2). 0 10 20 30 40 50 60 5 6 7 8 9 10 11 12...

Ngày tải lên: 10/08/2014, 02:20

... day of January 2006 (quality 0 ,17 ) is presented at Fig .1. MLP_20 WY_H2O January 2006, 1 day - MLP_20 Time [min] 15 16 17 18 19 01 2 01 4 01 6 01 8 01 10 01 12 01 14 01 Fig 1. Measured and modeled ... 0 ,13 5 0 ,13 6 MLP _19 19 16 0 ,16 7 0 ,16 9 0 ,16 7 0 ,10 9 0 ,10 9 0 ,11 0 Tab .1. Results of the best ANN built at 1 month (LIN_04, MLP _18 ) and 1 yea...

Ngày tải lên: 10/08/2014, 02:20

... 444 4 31 0.068 428.2 426 10 EIL1 01 629 662 646 0 .12 7 653.3 639 75 TSP225 3 916 419 2 410 6 0.302 4044 8 71 11  Ł. Brocki, D. Koržinek Mathematical Analysis of Stability for Inverter Fed Synchronous ... a developing environment, it is in charge of the real-time program debugging, the execu- tion code downloading, real-time parameter and state monitoring, and real- time gain au...

Ngày tải lên: 10/08/2014, 02:20

... Syfert Z - transform s -1 1 1 1 1 . 2 − − − + z zT s -2 ( ) 21 212 2 1 212 21 1 01 . 12 1 1 01 . 12 −− −− − −− +− ++ = − ++ zz zzT z zzT s -3 ( ) 3 21 213 3 1 213 3 31 . 2 1 . 2 −−− −− − −− −+− + = − + zzz zzT z zzT s -4 ( ... ) 3 21 213 3 1 213 3 31 . 2 1 . 2 −−− −− − −− −+− + = − + zzz zzT z zzT s -4 ( ) 720 46 41 4 . 6720 1 4 ....

Ngày tải lên: 10/08/2014, 02:20

... Parameter 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 min min min min % % min % min % min % min % min % min % min % min min min min Set of parameter Total recording time ... D* (10 ) and the recombination index of radiation quality Q 4 [5]. 4 Q )10 (D* )10 (*H ×= (1) where D* (10 ) is the absorbed dose in the appropriate phantom, simulating...

Ngày tải lên: 10/08/2014, 02:20

... s. 0 50 10 0 15 0 200 250 300 350 400 0 50 10 0 15 0 200 250 300 350 400 450 coil inductance *10 ^ -1 0[H] electromagnetic force *10 ^-4 [N] x (1) y (1) x (1) y(2) x (10 )y (10 ) x(2)y(5) x(3)y (10 ) x(2)y (10 ) x(8)y(2 ) x(5)y(2 ) x(3)y(2) x (10 )y(2 ) x (1) y(5) x (1) y(8 ) x(2)y (1) x(3)y (1) x(5)y (1) x(8)y (1) x (10 )y (1) x (1) y (10 ) x(5)y (10 ) x (10 )y(3)...

Ngày tải lên: 10/08/2014, 02:20

... Sobotáles, 2004 33 9Mechatronics aspects of in- pipe minimachine on screw-nut principle design Fig.2 3D model of the in- pipe minimachine 3. Kinematics Analyse of the Minimachine Regarding to the requirements ... natural geometry grains have been successfully tested in microgrooving. 1 2 1 2 3 4 5 5 Fig. 4. Diamond turning tool with cutting edge having natural geometry of the cr...

Ngày tải lên: 10/08/2014, 02:20

... quantity of fuel, etc.). A -1 5 -1 0 -5 0 5 10 15 -3 0 -2 0 -1 0 0 10 20 30 odchylka [%] chy ba diagn ozy [% ] neodpružená hmota odpružená hmota -2 0 -1 5 -1 0 -5 0 5 10 -3 0 -2 0 -1 0 0 10 20 30 odchylka ... ~ )( )( )( )( ~ )( )( ~ )( )( )( )( ~ )( )( ~~ 0022 13 14 1 10 20 5 13 15 2 1 2 3 1 2 42 20 4 13 14 203 13 15 2 1...

Ngày tải lên: 10/08/2014, 02:20