Recent Advances in Mechatronics - Ryszard Jabonski et al (Eds) Episode 1 Part 6 potx

... Parameter 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 min min min min % % min % min % min % min % min % min % min % min min min min Set of parameter Total recording time ... allows examination of e.g. total endoprothesis of hip joint (Fig. 2) eventually spinal element (Fig. 3). In the case of fixa- tor application to spinal segment a surgeon is a...

Ngày tải lên: 10/08/2014, 02:20

... where:Co - static capacity of the transducer, C - equivalent mechanical capacity, L - equivalent mechanical inductance, R - equivalent resistance, Rp = Rm + Ra, where: Rm - equivalent mechanical ... scene cut (fig. 3). Although it may cause some problems with coding, observers seem not to react to this incident at all (fig. 2). 0 10 20 30 40 50 60 5 6 7 8 9 10...

Ngày tải lên: 10/08/2014, 02:20

... 1 day of January 20 06 (quality 0 ,17 ) is presented at Fig .1. MLP_20 WY_H2O January 20 06, 1 day - MLP_20 Time [min] 15 16 17 18 19 01 2 01 4 01 6 01 8 01 10 01 12 01 14 01 Fig 1. Measured and modeled ... val. Err. tst Qual. learn. Qual. val. Qual. tst LIN_04 17 - 0, 263 0, 265 0, 267 0 ,18 8 0 ,19 0 0 ,18 9 LIN_08 17 - 0,380 0,3 76 0,374 0,...

Ngày tải lên: 10/08/2014, 02:20

... Reasoning 15 (19 96) 2 5-4 7. [3] S. W. Leung, J. W. Minett “The Use of Fuzzy Spaces in Signal Detection”, Fuzzy Sets and Systems 11 4 (2000) 17 5 -1 84. [4] M. Marseguerra, E. Zio, P. Baraldi, A. ... 1e+5 Parameter value 0 50 10 0 15 0 200 250 300 speed of rotation [1/ min] 0 2e+4 4e+4 6e+4 8e+4 1e+5 Parameter value 67 82 67 83 67 84 67 85 67 86 6787 Fig. 2. Dependence of...

Ngày tải lên: 10/08/2014, 02:20

... 444 4 31 0. 068 428.2 4 26 10 EIL1 01 62 9 66 2 64 6 0 .12 7 65 3.3 63 9 75 TSP225 3 9 16 419 2 410 6 0.302 4044 8 71 11  Ł. Brocki, D. Koržinek Mathematical Analysis of Stability for Inverter Fed Synchronous ... Romania, 16 . Table 1 Basis stereo [mm] X [mm] Y [mm] Z [mm] 1 1500 27,22 64 ,29 853 ,14 2 15 00 26, 96 64,48 853,00 3 15 00 27,43 64 ,08 852,...

Ngày tải lên: 10/08/2014, 02:20

... Syfert Z - transform s -1 1 1 1 1 . 2 − − − + z zT s -2 ( ) 21 212 2 1 212 21 1 01 . 12 1 1 01 . 12 −− −− − −− +− ++ = − ++ zz zzT z zzT s -3 ( ) 3 21 213 3 1 213 3 31 . 2 1 . 2 −−− −− − −− −+− + = − + zzz zzT z zzT s -4 ( ... ) 3 21 213 3 1 213 3 31 . 2 1 . 2 −−− −− − −− −+− + = − + zzz zzT z zzT s -4 ( ) 720 46 41 4 . 67 20 1...

Ngày tải lên: 10/08/2014, 02:20

... [%] µ - 3 σ µ + 3 σ p-value “p” 3 .10 1 0.004522 0 .15 % 3.087434 3 .11 4 566 0 .11 “l” 1. 5 56 0.003475 0.22% 1. 545575 1. 566 425 0. 069 parallel grooves etched during 15 min; “p - pitch; “l - width ... the grinding zone, and the influence of grains 2 76 B. Bałasz, T. Królikowski 1 1000 10 10 0 1 5 10 50 90 99 Time [Cycles] F(t) 6 27 10 10 12 15 3 2 4...

Ngày tải lên: 10/08/2014, 02:20

... Sobotáles, 2004 33 9Mechatronics aspects of in- pipe minimachine on screw-nut principle design Fig.2 3D model of the in- pipe minimachine 3. Kinematics Analyse of the Minimachine Regarding to the requirements ... natural geometry grains have been successfully tested in microgrooving. 1 2 1 2 3 4 5 5 Fig. 4. Diamond turning tool with cutting edge having natural geometry of the cr...

Ngày tải lên: 10/08/2014, 02:20

... 45 The quality of grinidng wheel: 500P Grinding wheel NC / Grinding wheel C Grinding wheel K45 / Grinding wheel C Grinding wheel K90 / Grinding wheel C Fig. 1. The influence of technological system ... 45 The quality of grinding wheel: 500E Grinding wheel NC / Grinding wheel C Grinding wheel K45 / Grinding wheel C Grinding wheel K90 / Grinding wheel C Fig. 2. The influence of technolog...

Ngày tải lên: 10/08/2014, 02:20

... quantity of fuel, etc.). A -1 5 -1 0 -5 0 5 10 15 -3 0 -2 0 -1 0 0 10 20 30 odchylka [%] chy ba diagn ozy [% ] neodpružená hmota odpružená hmota -2 0 -1 5 -1 0 -5 0 5 10 -3 0 -2 0 -1 0 0 10 20 30 odchylka ... equations (6) are ),( ~ ~ 0 011 1 uxfux +=  , (10 a) ),( ~ )( )( ~ 1 ~ )( )( )( )( ~ )( )( ~ )( )( )( )( ~ )( )( ~~ 0022 13 14 1...

Ngày tải lên: 10/08/2014, 02:20