Build A Remote-Controlled Robot part 11 ppt

... the robot s arms, drink dispenser, and head. ARMS Questor’s arms are very simple to make and install; however, care should be taken when fabricating them because errors in the parts may affect ... fas- tening the parts together. Once assembled, check to see that the arms are the same height and length. Do this by standing them next to each other. If the arms are not correct, all that may ......

Ngày tải lên: 10/08/2014, 01:22

... They have the advantages of being readily available and being designed to be safe, because they are sealed. Another advantage is that the battery charger and plug needed come with the batteries ... a break. They don’t get sick (although when they do break down, they can be easily repaired or even replaced), ask for pay raises, or any pay for that matter, and can be retrained to do another ....

Ngày tải lên: 27/06/2014, 18:20

... All trademarks are trademarks of their respective owners. Rather than put a trademark symbol after every occurrence of a trademarked name, we use names in an editorial fashion only, and to the ... the popular Star Wars notion of robots. A second, more-precise definition is stated by the Robot Institute of America. It reads: A robot is a programmable mul- tifunctional manipulator...

Ngày tải lên: 19/01/2014, 20:20

... the robot via a long wire or cable. The advantages of this system are that it is simple to build and costs little to construct. The main disadvantages are limited range and the cable itself can ... tools found in a home workshop and parts available in local hard- ware and electronics stores. However, there are a few parts you will have to order. The following list of what I’ve deter...

Ngày tải lên: 27/06/2014, 15:20

... position. ter, but makes it water resistant. You may opt as I have to fiberglass the platform. Fiberglass also provides water protec- tion and adds strength to the platform. Fiberglass is very easy to work ... (especially on a flat surface) so if you follow the directions on the package, you should have no problems. If you do use fiberglass, use a kit with a clear resin so you can locat...

Ngày tải lên: 10/08/2014, 01:22

... remove the motherboard and drill four 1/8-inch-diameter holes where marked, being careful not to damage the parts already mounted on the motherboard. Attach the motherboard to the angles using four ... dispenser operates in a rather straightforward manner; pushing the con- trol button on Questor’s wrist activates a small (and slightly noisy) 12-volt pump. This pump draws fluid out of a...

Ngày tải lên: 10/08/2014, 01:22

... place. later in this chapter. Also note the rubber gasket around the vacuum cleaner motor that you can attach at this time. To mount the pots and switches, poke a hole through the front of the panel ... skirt is made of black rubber floor matting available at any hardware store. You will need approximately a 2- ϫ 2-foot piece of matting; from this cut four 6- ϫ 20-inch strips, one for eac...

Ngày tải lên: 10/08/2014, 05:20

... A similar packing material can be purchased from GL Sciences, Tokyo, Japan. d)  e reagent is a quaternary ammonium compound to be used as a phase-transfer-catalyst. Another group reported a ... with an English abstract) 12) Kage S, Nagata T, Kimura K et al. (1988) Extractive alkylation and gas chromatographic analysis of sulfide. J Forensic Sci 33:217–222 13) Miki A, Tsuchihash...

Ngày tải lên: 26/01/2014, 18:20

...

Ngày tải lên: 02/07/2014, 13:20

... external platform. The two methods of authentication that are available in BCS are: • Claims-based authentication • Credentials-based authentication Authentication of BCS Access with Claims ... ensure that application developers are aware of the options for authenticating data access from the BCS. You must associate each with an authentication mode, which is associated with an externa...

Ngày tải lên: 04/07/2014, 13:20