SolidWorks 2010 bible phần 1 pptx

... 10 11 Terminating ribs 10 11 Using thin features 10 13 Using Draft 10 14 Neutral Plane draft 10 14 Parting Line draft 10 15 Step draft 10 15 Some draft limitations 10 16 What to do when draft fails 10 17 DraftXpert ... feature 910 Fixed Face 910 Jog Offset 911 Fix projected length 911 Jog Position 911 Jog Angle 911 Sketched Bend feature 911 Closed Corner feature 912 Faces t...

Ngày tải lên: 09/08/2014, 12:21

... following 05_577395 flast.qxd 12 /14 /04 11 :55 PM Page xxxii 05_577395 flast.qxd 12 /14 /04 11 :55 PM Page xlii SUSE ™ Linux ® 9 Bible 01_ 577395 ffirs.qxd 12 /14 /04 11 :56 PM Page i xl Introduction any ... fpref.qxd 12 /14 /04 11 :58 PM Page xii SUSE ™ Linux ® 9 Bible 05_577395 flast.qxd 12 /14 /04 11 :55 PM Page xli SUSE ™ Linux ® 9 Bible Justin Davies, Roger Whittaker, an...

Ngày tải lên: 24/07/2014, 02:20

... with the Bristle Brush 11 1 Making a custom brush 11 2 Understanding colorization tips 11 3 Checking out the Brush libraries 11 4 Using Variable Width Strokes 11 6 Summary 11 6 Chapter 5: Creating ... ................ 11 9 Making Basic Shapes 11 9 Drawing shapes from their centers 12 2 Drawing symmetric shapes 12 2 Drawing shapes at an angle 12 2 Drawing rectangles u...

Ngày tải lên: 08/08/2014, 19:23

... Copy Settings Wizard To use the Copy Settings Wizard, follow these steps: 1. Close SolidWorks. Part I: SolidWorks Basics 11 8 FIGURE 3.33 The Fully Define Sketch interface Exploring Sketch Settings In ... create split lines. Part I: SolidWorks Basics 86 10 . Press R. The rectangle macro runs and draws a sketch rectangle on the Front plane, cen- tered on the origin. 11 . Press...

Ngày tải lên: 09/08/2014, 12:21

... entity that you want to reattach the relation to. 12 . Exit the sketch. 13 . Drag the rollback bar to just before CutExtrude1. Edit 3DSketch1. This sketch is overdefined. If the Sketch Relations ... Techniques 19 9 14 . Select the features Extrude1, Fillet7, and Fillet6 from the FeatureManager so that they are displayed in the Selection list of the Appearances window. Select a color...

Ngày tải lên: 09/08/2014, 12:21

... follows: Spacing = Length / ((Instances -1) +1) The Instances 1 term stands for the number of spacings. If you have two holes, then there is only one spacing. The +1 term stands for the two half-spacings ... fillets Part II: Building Intelligence into Your Parts 356 is perfectly acceptable, as is 1+ 1/2 or 1 1/2 In the second case in this example, the plus symbol is understood. Other t...

Ngày tải lên: 09/08/2014, 12:21

... FIGURE 11 .24 Deviation analysis of an existing part Select RMB then select tangency FIGURE 11 .25 Rolling back to just after the spiral Chapter 11 : Editing and Evaluation 4 31 FIGURE 11 .28 Sketch3 ... shown in Figure 11 .26. FIGURE 11 .26 Preparing for the Fit Spline 8. Select both the converted spiral and the line, and click Tools ➪ Spline Tools ➪ Fit Spline. Set the Tolerance...

Ngày tải lên: 09/08/2014, 12:21

... Figure 17 .11 shows a Toolbox part with the FeatureManager and ConfigurationManager open, showing several configurations that Toolbox created in this particular fastener. FIGURE 17 .11 A Toolbox ... out-of-context symbol. Chapter 16 : Modeling in Context 555 FIGURE 16 .11 Using multiple contexts In-context feature Part IV: Creating and Using Libraries 592 FIGURE 17 .10 Create hole...

Ngày tải lên: 09/08/2014, 12:21

... appear. Creating the view shown in Figure 21. 10 requires only a single sketched line, while Figure 21. 11 requires perpendicular sketched lines. FIGURE 21. 11 A Section View requiring perpendicular ... Figure 21. 11, but the resulting view is different, as shown in Figure 21. 12. The finished view aligns with the selected sketch element. Chapter 21: Working with Drawing Views 705 FIGU...

Ngày tải lên: 09/08/2014, 12:21

... use of literally hundreds of solid bodies, and is shown in Figure 26 .11 and Figure 26 .12 . Part VI: Using Advanced Techniques 814 FIGURE 26.4 The Indent feature using a tool body On the CD-ROM To ... creating drawings of individual parts, not that it cannot be done (remember that starting in SolidWorks 2 010 you can now specify bodies from a part to be used in a drawing view), just...

Ngày tải lên: 09/08/2014, 12:21