Modelling with AutoCAD 2004 phần 5 docx
... displayed with varying width or with arc segments 4 The command is activated from the menu bar or by command line entry. 138 Modelling with AutoCAD 2004 164 Modelling with AUTOCAD 2004 4 The ... point: 70,70,100 85, 70,1 25 Endpoint: 80, 35, 100 90 ,50 ,1 25 Endpoint: 130, 45, 100 130,60,1 25 Endpoint: 170,90,100 130,80,1 25 Endpoint: 100,120,100 close Endpoint: close...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 10 docx
... render with a type and to a destination. Figure 45. 2 Light symbols with ‘names’ added. Rendering 3 25 3D orbit with materials attached AutoCAD 2004 allows the 3D orbit command to be used with materials ... shadows 3. Distant light with: a) name: D1 b) intensity: 0. 75 c) direction TO: 50 ,Ϫ20, 150 d) direction FROM: @ 50 , 50 ,50 e) shadows (volumes/ray traced) on 7 Make a...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 1 potx
... 6 Introducing 3D AutoCAD ISBN 0 340 61 456 0 Solid Modelling with AutoCAD ISBN 0 340 63204 6 Assignments in AutoCAD ISBN 0 340 69181 6 Starting with AutoCAD LT ISBN 0 340 6 254 3 0 Advancing with AutoCAD ... 340 6 457 9 2 3D Draughting using AutoCAD ISBN 0 340 67782 1 Beginning AutoCAD R13 for Windows ISBN 0 340 6 457 2 5 Advancing with AutoCAD R13 for Windows ISBN...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 2 ppt
... saved UCS. Refer to Fig. 5. 5 and: 1 Ensure the 3DWFM is displayed with the saved UCSs 2 Restore UCS SLOPE1 current – Fig. 5. 5(a) 40 Modelling with AutoCAD 2004 Figure 5. 4 The UCS dialogue box ... axis enter ؊90 ϽRϾ – Fig. 5. 1(h) 5 Menu bar with Tools-New UCS-Z and: prompt Specify rotation angle about the Z axis enter ؊90 ϽRϾ – Fig. 5. 1(i). The UCS 35 28 Modelling w...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 3 pdf
... Isometric 2 25 35. 3 SE Isometric 3 15 35. 3 NE Isometric 45 35. 3 NW Isometric 1 35 35. 3 72 Modelling with AutoCAD 2004 Figure 10 .5 3D Views – the isometric presets with the TEST3D model. Viewpoint ... ZOOM command with other values, e.g. 0. 75, 1. 25, 1 .5 etc. 3D Views (Viewpoints) 81 Figure 10.14 Centre viewport Example 2 – TEST3D by centre/magnification. 90 Modelling...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 6 pps
... angle values: angle in XY plane angle from XY plane a) 35 35 b) 35 Ϫ 35 c) Ϫ 35 35 d) Ϫ 35 Ϫ 35 4 The option can be considered similar to VPOINT ROTATE 5 When all the above entries have been completed, ... option enter the following angle values: angle in XY plane angle from XY plane a) 35 35 b) 35 Ϫ 35 c) Ϫ 35 35 d) Ϫ 35 Ϫ 35 4 The option can be used to give the same effect...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 7 doc
... essential for the AutoCAD creation of solid composites from primitives. 220 Modelling with AutoCAD 2004 200 Modelling with AutoCAD 2004 4 Change the colour of this wedge to blue 5 At the command ... corner: 1 65, 25 opposite corner: @160,70 b) first corner: 1 65, 95 opposite corner: @160, 155 c) first corner: 3 25, 95 opposite corner: @70, 155 4 In model space: a) make...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 8 doc
... circles: a) centre: 50 ,0, radius: 50 b) centre: 0 ,50 , radius: 60 c) centre: 75, 75, radius: 75 4 Make a new layer: BND, colour blue and current 250 Modelling with AutoCAD 2004 Figure 36.3 Region ... 39.1 Using the PROFILE command with SLIPBL. 256 Modelling with AutoCAD 2004 2 With the 3D viewport active, create a box primitive with: a) corner: 0,0,0 b) length: 7...
Ngày tải lên: 09/08/2014, 11:21
Modelling with AutoCAD 2004 phần 9 ppt
... 20) with: a) centre: 150 ,50 ,0 b) diameter: 5 and height: 25 2 Block as SPIND with insertion base point: 150 ,50 ,0. Hand (colour number 124) 1 Create a cylinder with centre: 180,20,0, diameter: 5 ... objects to have the ‘correct’ value. 276 Modelling with AutoCAD 2004 Figure 40.1 Adding dimensions in model and paper space. 284 Modelling with AutoCAD 2004 3 Using t...
Ngày tải lên: 09/08/2014, 11:21