Modelling with AutoCAD 2004 phần 1 potx

... PFACE 10 2 Chapter 15 3DMESH 11 1 Chapter 16 Ruled surface 11 4 Chapter 17 Tabulated surface 12 2 Chapter 18 Revolved surface 12 5 Chapter 19 Edge surface 12 9 Chapter 20 3D polyline 13 6 Chapter 21 3D ... 5 Advancing with AutoCAD R13 for Windows ISBN 0 340 6 918 7 5 Modelling with AutoCAD R13 for Windows ISBN 0 340 692 51 0 Using AutoLISP with AutoCAD ISBN 0 340 7...

Ngày tải lên: 09/08/2014, 11:21

... icon with: Plane 12 34 Plane 15 64 Plane 3764 Plane 7896 Start 30,30,0 30,30,0 13 0 ,13 0,0 13 0 ,13 0 ,10 0 Next @10 0,0,0 @0,0 ,10 0 @0,0 ,10 0 @0 ,10 0,0 Next @0 ,10 0,0 @0 ,10 0,0 @ 10 0,0,0 @ 10 0,0,0 Next @ 10 0,0,0 ... UCS enter TOP ϽRϾ 12 With layer OBJECTS current draw a circle with centre: 60,20 and radius: 15 13 With layer TEXT current, add single line text using: a)...

Ngày tải lên: 09/08/2014, 11:21

... rotate view 0,0 ,1 0,90 top 0, 1, 0 270,0 front 1, 0,0 0,0 right 0 ,1, 0 90,0 rear 1, 0,0 18 0,0 left 0,0, 10 ,Ϫ90 bottom 1, 1 ,1 45,35 3D from above 1, 1, 1 13 5,Ϫ35 3D from below 11 This completes ... (Fig. 10 .4) 1, 0,0 from right c 0 ,1, 0 from rear d 1, 0,0 from left e 0,0, 1 from below f 1, 1 ,1 3D from above g 1, 1, 1 3D from below h 8 Restore the original SE Isometric...

Ngày tải lên: 09/08/2014, 11:21

... 7 ,10 7 ,11 7 ,12 7 ,13 c) 8,7 8,8 8,9 8 ,10 8 ,11 8 ,12 8 ,13 d) 9,6 9,7 9,8 9,9 9 ,10 9 ,11 9 ,12 9 ,13 9 ,14 e) 10 ,6 10 ,7 10 ,8 10 ,9 10 ,10 10 ,11 10 ,12 10 ,13 10 ,14 f) 11 ,6 11 ,7 11 ,8 11 ,9 11 ,10 11 ,11 11 ,12 ... 11 ,12 11 ,13 11 ,14 g) 12 ,7 12 ,8 12 ,9 12 ,10 12 ,11 12 ,12 12 ,13 h) 13 ,7 13 ,8 13 ,9 13 ,10 13 ,11 13 ,12 13 ,13 i) 14 ,9...

Ngày tải lên: 09/08/2014, 11:21

... Point option with the following entries: target point camera point a) 0,0,0 1, 0,0 b) 0,0,0 0 ,1, 0 c) 0,0,0 0,0 ,1 d) 0,0,0 1, 1,0 e) 0,0,0 1, 0 ,1 f) 0,0,0 1, 1 ,1 g) 1, 2,3 0,0,0 h) 0,0,0 1, 2,3 7 The ... Fig. 24 .1. B(b) c) prompt Enter option [CAmera/TArget/etc enter H ϽRϾ – the hide option and house displayed with hidden line removal – Fig. 24. 1. B(c) 17 2 Modelling w...

Ngày tải lên: 09/08/2014, 11:21

... model 1 – a machine support 223 204 Modelling with AutoCAD 2004 11 With MVLAY1 tab active, zoom-extents then zoom to a factor of 1. 25 in all viewports 12 Hide, shade, 3D orbit then save as MODR2004\CONPRIM. The ... operations. 16 Restore UCS BASE 17 Create a cylinder with: a) centre: 20 ,15 ,0 b) radius: 9 c) height: 25 d) colour: number 17 4 18 Multiple copy the cylinde...

Ngày tải lên: 09/08/2014, 11:21

... support ( 31) 812 70.75 10 22333.68 Backing plate (32) 3 817 1.70 98283.83 Pipe/flange (33) 19 0938 .19 13 05275.35 Mass Properties file When the mass properties command is used with a solid model, the AutoCAD ... colour blue and current 250 Modelling with AutoCAD 2004 Figure 36.3 Region Example 3 – created from a boundary. 244 Modelling with AutoCAD 2004 Solids editing E...

Ngày tải lên: 09/08/2014, 11:21

... mean? 288 Modelling with AutoCAD 2004 A detailed drawing 2 81 2 Create three wedges using the following information: corner length width height wedge 1 6 ,12 ,25 18 61 5 wedge 2 6 ,12 ,25 12 Ϫ65 wedge ... resembles Fig. 41. 1(b) 6 Create another two wedges with: corner length width height wedge 4 6,0,25 18 12 5 wedge 5 24 ,12 ,25 12 18 5 7 Rotate wedge 5 about the point 24...

Ngày tải lên: 09/08/2014, 11:21

... name: SC1 2. pick Views: V1 3. pick Lights: *ALL*, i.e. both P1 and D1 4. pick OK prompt Scenes dialogue box with SC1 listed respond pick OK 320 Modelling with AutoCAD 2004 4 Create a cylinder with: a) ... Clock with materials attached. 2D edge surface 12 9 3D array 14 7 3D coordinates 20 3D edge surface 13 0 3D extend 15 0 3D orbit 18 6 3D trim 15 0 Active viewport 59 Ali...

Ngày tải lên: 09/08/2014, 11:21