Learning AutoCAD 2010, Volume 1 phần 8 pot

... circles 2 and 3 = 10 3.9447 mm Distance between circles 2 and 4 = 10 5.6296 mm 11 . Angle = 13 1 degrees Delta Y = 44.9275 mm 13 . X = 253 .13 53Y = 0.0000Z = 0.0000 14 . Net area ... it in the Text Window by pressing F2. Distance = 15 7 .19 24, Angle in XY Plane = 34, Angle from XY Plane = 0Delta X = 13 0.39 38, Delta Y = 87 . 788 9, Delta Z = 0.0000 The...

Ngày tải lên: 09/08/2014, 11:20

... panel automatically displays two property rows. 11 . On the status bar, right-click Quick Properties. Click Settings. 12 . In the Drafting Settings dialog box, Quick Properties ... Click OK. 13 . Select a dimension in the drawing. The Quick Properties panel automatically expands. 14 . Press ESC to clear the selected dimension. 15 ....

Ngày tải lên: 09/08/2014, 11:20

... Objects 10 . To remove the construction lines: ■ Start the Erase command. ■ Select the lines indicated in the following image. Press ENTER. 11 . Your completed drawing. 12 . ... (1) . ■ Select the object to join (2). ■ Press ENTER to complete the command. 5. To Join the arc segments and close them. Method 1: ■ Begin the Join command. ■ Select one...

Ngày tải lên: 09/08/2014, 11:20

... lengths at 1 for the same results. 3. To chamfer using the polyline option: ■ Draw another 8 x 6 rectangle (see #1) . ■ Begin the Chamfer command. ■ See that the current chamfer length is 1 and ... Objects 11 . To select a door to relocate within a wall: ■ Start the Stretch command. ■ Click near point (1) and then point (2) to define the crossing window. ■ Press ENTER....

Ngày tải lên: 09/08/2014, 11:20

... PolarSnap 11 7 Using Polar Tracking and PolarSnap 11 8 Exercise: Use Polar Tracking and PolarSnap 12 5 Lesson: Using Object Snap Tracking 12 8 About Object Snap Tracking 12 9 Using Object Snap Tracking 13 0 Exercise: ... to your drawing. AutoCAD ® 2 010 Autodesk Official Training Guide Essentials Autodesk Certification Preparation 001B1-050000-CM10A April 2009 Learning A utoCAD...

Ngày tải lên: 09/08/2014, 11:20

... Polar angle is 90. ■ Enter 1 and press ENTER. ■ Drag to < 0, and enter 1 and press ENTER. ■ Drag to < 90, and enter 1. 5 and press ENTER. ■ Drag to < 18 0, and enter 1 and press ENTER. ■ Drag ... @ 38. 500< ; 18 0 puts the interface in Relative Coordinate mode and places the values in the correct input fields. Press ENTER to complete the Copy command. 36 ■ Chapter...

Ngày tải lên: 09/08/2014, 11:20

... line. 10 . To draw a line perpendicular to the last: ■ Drag the cursor upward making sure that the angle field displays 90 degrees. ■ Enter 10 0. Press ENTER. 11 . To draw ... ■ 81 Procedure: Using Undo and Redo The following steps give an overview of how to use the Undo and Redo commands in the drawing. 1. On the Quick Access Toolbar, click Undo...

Ngày tải lên: 09/08/2014, 11:20

... with Units ■ 14 7 11 . For the next point: ■ Move the cursor to the left. ■ Enter 44'-5". Press TAB. ■ Enter 18 0. Press TAB. ■ Click anywhere in the drawing. 12 . Right-click ... next point: ■ Move the cursor to the left. ■ Enter 15 '-3". Press TAB. ■ Enter 18 0. Press TAB. ■ Click anywhere in the drawing. 10 . For the next point: ■ Move the...

Ngày tải lên: 09/08/2014, 11:20

... basepoint. ■ Enter a rotation angle of 10 . Press ENTER. ■ Notice that the object is rotated 10 degrees counterclockwise. 18 4 ■ Chapter 3: Manipulating Objects 8. To position the desk and ... Position the cursor so that the polar angle displays 18 0 degrees. Click to select that point. 10 . Close all files. Do not save. 214 ■ Chapter 3: Manipulating Obj...

Ngày tải lên: 09/08/2014, 11:20

... 2 21 Practice Exercise: Creating an Array of Objects In this practice exercise, you draw a 1 x 1 rectangle and create an array using the Polar and Rectangular array options. 1. ... Introduction in Volume 1. Lesson: Creating Object Patterns ■ 219 Procedure: Creating a Polar Array of Objects The following steps are an overview of creating polar arrays. 1...

Ngày tải lên: 09/08/2014, 11:20