Learning AutoCAD 2010, Volume 1 phần 4 docx

... with Units ■ 14 7 11 . For the next point: ■ Move the cursor to the left. ■ Enter 44 '-5". Press TAB. ■ Enter 18 0. Press TAB. ■ Click anywhere in the drawing. 12 . Right-click ... Introduction in Volume 1. 14 6 ■ Chapter 2: Creating Basic Drawings 4. For the next point: ■ Move the cursor down and to the right. ■ Enter 2&apos ;4. 25. Press TAB. E...

Ngày tải lên: 09/08/2014, 11:20

... line. 10 . To draw a line perpendicular to the last: ■ Drag the cursor upward making sure that the angle field displays 90 degrees. ■ Enter 10 0. Press ENTER. 11 . To draw ... 11 6 ■ Chapter 2: Creating Basic Drawings 9. Repeat the previous step on the opposite side of the part. 10 . Close all files. Do not save. Lesson: Using Object Snaps...

Ngày tải lên: 09/08/2014, 11:20

... Tracking 13 6 Lesson: Working with Units 13 9 About Units 14 0 Setting Units 14 1 Exercise: Use Architectural Units 14 5 Exercise: Use Surveyor's Units 14 8 Challenge Exercise: Architectural 15 0 Challenge ... Filleted Corner 41 0 Lesson: Creating an Angled Corner Between Two Objects 41 3 Creating Chamfers 41 4 Exercise: Create a Chamfered Corner 41 9 Lesson: Changing Part of...

Ngày tải lên: 09/08/2014, 11:20

... selection. 11 . Close all files. Do not save. Chapter Summary ■ 41 Chapter Summary Now that you have been introduced to several core features, you can begin learning how to ... Polar angle is 90. ■ Enter 1 and press ENTER. ■ Drag to < 0, and enter 1 and press ENTER. ■ Drag to < 90, and enter 1. 5 and press ENTER. ■ Drag to < 18 0, and enter 1 and p...

Ngày tải lên: 09/08/2014, 11:20

... variable set to 1. 1. Begin by setting the MIRRTEXT system variable to 1. This turns the mirroring of text on. ■ At the Command line, enter MIRRTEXT and press ENTER. ■ Enter 1 and press ENTER. ... left corner as the basepoint. ■ Enter a rotation angle of 10 . Press ENTER. ■ Notice that the object is rotated 10 degrees counterclockwise. 18 4 ■ Chapter 3: Manipulatin...

Ngày tải lên: 09/08/2014, 11:20

... Array dialog box, for Rows, enter 4. ■ For Columns, enter 2. ■ Under Offset Distance and Direction, click Pick Both Offsets. Challenge Exercise: Grips ■ 2 41 11 . Use the Copy and Base Point ... Introduction in Volume 1. Lesson: Creating Object Patterns ■ 219 Procedure: Creating a Polar Array of Objects The following steps are an overview of creating polar arrays....

Ngày tải lên: 09/08/2014, 11:20

... selecting Other. 1. Select one or more objects in your drawing that need to have their linetype changed. 3 04 ■ Chapter 4: Drawing Organization and Inquiry Commands 4. To match ... automatically expands. 14 . Press ESC to clear the selected dimension. 15 . Close all files. Do not save. Lesson: Changing Object Properties ■ 289 4. To mov...

Ngày tải lên: 09/08/2014, 11:20

... = 10 3. 944 7 mm Distance between circles 2 and 4 = 10 5.6296 mm 11 . Angle = 13 1 degrees Delta Y = 44 .9275 mm 13 . X = 253 .13 53Y = 0.0000Z = 0.0000 14 . Net area = 242 55.3 940 mm ... Distance = 55 mm Angle = 212 degrees 4. Radius for circle 2 = 17 .25 mm Radius for circle 4 = 10 .00 mm 5. Object type = LWPOLYLINE Area = 17 64. 00 m...

Ngày tải lên: 09/08/2014, 11:20

... break objects. 3 84 ■ Chapter 5: Altering Objects 14 . To complete the pocket: ■ When prompted for the object to offset, select the vertical line in the lower left view (1) . ■ When prompted ... Objects 10 . To remove the construction lines: ■ Start the Erase command. ■ Select the lines indicated in the following image. Press ENTER. 11 . Your completed drawing....

Ngày tải lên: 09/08/2014, 11:20

... zero-radius fillet. 12 . Close all files without saving. 44 6 ■ Chapter 5: Altering Objects Lesson: Creating an Angled Corner Between Two Objects ■ 41 9 Exercise: Create a Chamfered ... drawing should look like the following image. 12 . Close all files without saving. Challenge Exercise: Mechanical ■ 4 41 4. Create and edit geometry so the side...

Ngày tải lên: 09/08/2014, 11:20