Google SketchUp Cookbook phần 4 pps
Google SketchUp Cookbook phần 4 pps
... indicated in Figure 5 -43 .
Figure 5 -43
Move in the red direction then hold Shift while 6.
clicking the roof face (Figure 5 -44 ). This is another
way to use a double constraint.
Figure 5 -44
Complete the ... scale (Figure 4- 83).
Figure 4- 81
Figure 4- 82
Figure 4- 83
For the scale value, enter 8. –1. Then move the copy
so that the spacing between the lenses looks correct
(Figure...
Google SketchUp Cookbook phần 3 ppsx
... shown in Figure 4- 41.
Make the leg a component and make three more 13.
copies to support a table.
Figure 4- 40 Figure 4- 41
For the table top, draw a rectangle on top of the set 14.
of four legs. ...
90-degree copy (Figure 4- 17).
Pull this copied face along the next edge .4.
Figure 4- 17
Repeat steps 2 through 4 for the remaining two 5.
edges of the table (Figure 4- 18).
Figur...
Google SketchUp Cookbook phần 8 pps
... where indicated in Figure 11 -46 .
Figure 11 -46
This creates two parallel section planes, one at the
front of the house and one toward the back (Figure
11 -47 ).
Figure 11 -47
Orbit so you are facing ... can
still see the graphic below.
Figure 10 -41
Figure 10 -42
Figure 10 -43
Creating a Grid
|
259
Select and rotate-copy all of the construction lines 4.
90 degrees (Figure 10-33)...
Google SketchUp Cookbook phần 10 pps
... location,
338–339
using Google Earth, 331–3 34
Get Current View tool, 151
Get Models, 319, 344
glasses, 102–106
lens frame, 1 04 106
Google collections, 344
Google Earth, 317– 342
3D Buildings layer, ...
Follow Me face, 38 40
perpendicular paths, 51
preselect edges of path, 28
preselect face as path, 27
roofs with uniform slope, 92– 94
round or lathed objects, 41 44
spheres, 4...
The VHDL Cookbook phần 4 ppsx
... assignment:
s <= '1' after 4 ns, '0' after 20 ns;
were executed. The two new transactions are added to the projected output
waveform:
4- 4 The VHDL Cookbook
on any of these signals ... the
initialization phase, and thereafter whenever either of
en or sel changes
value.
4.
VHDL Describes Behaviour 4- 3
time, they execute concurrently. A process is specified in...
Google SketchUp Cookbook phần 1 doc
... Contents
4. Advanced Intersect and Follow Me Techniques 79
4. 1 Creating Temporary Faces for Follow Me 80
4. 2 Rounding Corners 84
4.3 Creating Lathed Shapes 89
4. 4 Roofing with a Uniform Slope 92
4. 5 ... as shown in Figure 1 -44 .
Figure 1 -44
Click an adjacent octagon corner, and the Angle 7.
field informs you that the angle is 45 degrees (Fig-
ure 1 -45 ).
In this example, 45 d...
Google SketchUp Cookbook phần 2 potx
... on the edge closest to the Follow Me
face (Figure 2 -44 ).
Figure 2 -44
End the offset at the closest point on the Follow Me 5.
face (Figure 2 -45 ).
Now you can see why the previous Follow Me
operation ... of the 3.
first circle (Figure 2-72).
Figure 2-72
44
|
Chapter 2: Following Paths with Follow Me
If you extrude a vertical circle (Figure 2- 64) around a
far-off horizontal circle...
Google SketchUp Cookbook phần 5 ppt
... green and brown frames
meet (Figure 7 -44 ).
Figure 7 -44
Complete the rectangle along the cutting plane, ex -4.
tending past the edges of the window (Figure 7 -45 ).
Right-click on the rectangle and ... you can see into the
house (Figure 7- 54) .
Figure 7- 54
1 74
|
Chapter 7: Components: Efficiency in Repetition
Orbit to a view like the one shown in Figure 7 -43 , 2.
in which you c...
Google SketchUp Cookbook phần 6 pptx
... translucent, too (Figure
8 -47 )—which means the suspect can view his witnesses.
Figure 8 -47
This is easily fixed: paint this side of the window with
an opaque material (Figure 8 -48 ). Now the suspect ... it.
Figure 8 -40
Adjust the Opacity slider for the stone material. 6.
Now you can see through the skylight, while still
seeing a faint version of the stone pattern (Figure
8 -41 )....
Google SketchUp Cookbook phần 7 pdf
... half-circles for the
tires should be separate faces. Push back the extra
faces (Figure 9 -44 ).
Figure 9 -43
Figure 9 -44
To model the tires, use Push/Pull with the Ctrl/Op-7.
tion key on the half-circle ... side of the tire (Figure 9 -45 ).
Figure 9 -45
Repeat this Push/Pull operation for the other tires. 8.
Then trim the bottom of the truck to leave only the
tires. Figure 9 -46 sho...