autocad 2007 and autocad lt 2007 bible - phần 4 docx

... dimensions, ab 1 4- b.dwg, is in the Drawings folder on the CD-ROM. STEPS: Drawing Baseline and Continued Dimensions 1. Open ab 1 4- b.dwg from your CD-ROM. 2. Save the file as ab1 4- 0 3.dwg in your AutoCAD Bible ... Design, Inc., Fergus, Ontario, for this drawing. Using AutoCAD and AutoCAD LT fonts AutoCAD and AutoCAD LT fonts are simpler than TrueType fonts, and...

Ngày tải lên: 08/08/2014, 23:20

... 76.9 68.8 44 .4 20 4 20 76.9 76.9 60.7 44 .4 20 5 76.9 68.8 60.7 40 .4 20 6 30 68.8 68.8 54. 6 40 .4 20 7 68.8 61.7 54. 6 37.3 20 8 40 61.7 61.7 49 .5 37.3 20 9 45 61.7 55.6 49 .5 34. 8 20 < The temperature ... where p m T (45 s) is the center node, Mesh Size ∆ xp m T (45 s) x q ′′ (0 ,45 s) x q ′′ (L ,45 s) (mm) ( ° C) kW/m 2 kW/m 2 10 149 .8 -2 49 .8 + 149 .8 5 1...

Ngày tải lên: 08/08/2014, 17:20

... xii AutoCAD ® 2007 and AutoCAD LT ® 2007 Bible 01_7888 64 ffirs.qxp 5/22/06 7:10 PM Page i Preface W elcome to the AutoCAD 2007 and AutoCAD LT 2007 Bible. Whether you use AutoCAD or AutoCAD LT, ... whether this book is for you. If you are a new AutoCAD or AutoCAD LT user If you are new to AutoCAD or AutoCAD LT, the AutoCAD 2007 and AutoCAD...

Ngày tải lên: 08/08/2014, 23:20

... sizes. Table 5-3 : Standard Paper Sheet Sizes in the United States (in inches) Size Width Height Size Width Height A118 1 ⁄2 D 342 2 B1711 E 443 4 C2217 Table 5 -4 lists standard metric sheet sizes. Table 5 -4 : ... donuts and points, ab07-d.dwg, is in the Drawings folder on the CD-ROM. STEPS: Drawing Donuts and Points 1. Open ab07-d.dwg from the CD-ROM. 2. Save the file as ab0 7-0...

Ngày tải lên: 08/08/2014, 23:20

... you can create more- complex filters and save them. To create a filter, type filter ↵ on the command line to open the Object Selection Filters dialog box, as shown in Figure 1 0 -4 2. If you’ve already ... both a line and a polyline. This is a good example of a filter that you cannot cre- ate using Quick Select. Figure 1 0 -4 3: A filter that selects all lines and all polylines. Note...

Ngày tải lên: 08/08/2014, 23:20

... space, ab17-a .dwg and ab-17-a-blk.dwg, are in the Drawings folder on the CD-ROM. STEPS: Laying Out a Drawing in Paper Space 1. Open ab17-a.dwg from your CD-ROM. 2. Save the file as ab1 7-0 2.dwg ... You cannot create non-rect- angular viewports in AutoCAD LT. Tip 24_ 7888 64 ch17.qxp 5/22/06 7:20 PM Page 49 8 507 Chapter 17 ✦ Plotting and Printing Your Drawing 3. Set the plot-s...

Ngày tải lên: 08/08/2014, 23:20

... AutoCAD Bible\ databases\ab20-prt.xls worksheet. Click OK three times and close the Control Panel. 7. Open AutoCAD. Open ab20-a.dwg from the CD-ROM. Save it as ab2 0-0 1.dwg in your AutoCAD Bible ... xref. Copy ab19-b.dwg from the \Drawings folder and ab1 9-0 1.dwg from the \Results folder (both on the CD-ROM) to your AutoCAD Bible folder. Choose Insert ➪ External Refere...

Ngày tải lên: 08/08/2014, 23:20

... solids, ab 2 4- d.dwg, is in the Drawings folder on the CD-ROM. On the CD-ROM 33_7888 64 ch 24. qxp 5/22/06 7 :41 PM Page 782 775 Chapter 24 ✦ Creating Solids and Editing in 3D Figure 2 4- 9 : The desk ... Figure 2 4- 1 4 shows some lofted solids. The LOFT command is new for AutoCAD 2007. You can use this command to create an object with variations in shape along its length. Figure...

Ngày tải lên: 08/08/2014, 23:20

... drawings and files used in the following exercise on creating and configuring a sheet set, ab26-f-1.dwg, ab26-f-2.dwg, ab26-f-3.dwg, and ab26-f.dwt, are in the Drawings folder on the CD-ROM. STEPS: ... creating and using a tool palette, ab26-c.dwg and ab26-d.dwg, are in the Drawings folder on the CD-ROM. STEPS: Creating and Using a Tool Palette 1. Open ab26-c-dwg from the CD-ROM....

Ngày tải lên: 08/08/2014, 23:20

... Figure 3 2-3 : *2 ,4, PENNANT 044 ,02F,029,0 Figure 3 2-3 : The PENNANT shape. 5 6 7 8 9 1 0 F 43 2 B A CD E Start point 43 _7888 64 ch32.qxp 5/22/06 7: 34 PM Page 1029 1007 Chapter 30 ✦ Creating Macros and ... dialog box to modify the menu. In AutoCAD 2007 and AutoCAD LT 2007, the entire menu file is in XML format. This change occurred in AutoCAD 2006 and AutoCAD...

Ngày tải lên: 08/08/2014, 23:20