Gas Burners for Forges Furnaces and kilns phần 1 ppsx

... motors. Only hand tools are necessary for the fabrication of the burners and the forges, furnaces, and kilns. Construction plans for the forges, furnaces, and burners in this book are laid out ... panels and bellyband 10 . Constructing and mounting the burner collar and plate I I. Mounting front panels 12 . Mounting side panels 13 . Mounting the back panel an...

Ngày tải lên: 08/08/2014, 17:20

... nipple) (1 1) Two 11 8-inch NPT x 11 4-inch NPT bell reducers (12 ) 9 /16 -18 LH thread to 11 4 MPT outlet bushing or a 318 flared fitting (13 ) Two brass 311 6-inch inverted female nuts (14 ) Two 11 8 NPT ... plumbing, and heavy equipment repair. The bell reducer (part # 4) might not be available in 11 8-inch x 11 2-inch, but may be available in 11 4-inch x 11 2-inch...

Ngày tải lên: 08/08/2014, 17:20

... (preferably hex) (1 1) 11 8 NPT x 11 4 NPT bell reducer (or threaded bushing and 11 4 NPT coupling) (12 ) 911 6 -18 LH thread to 11 4 MPT Outlet Bushing or 318 flared fitting (13 ) 1/ 4-27 F x 11 8 M reducing ... sleeve (14 ) 11 8 NPT brass coupling (15 ) Four #8 x 32 x 11 2-inch SS set screws (16 ) Four #8 x 32 X 11 4-inch SS set screws (17 ) 11 8-inch X...

Ngày tải lên: 08/08/2014, 17:20

... steel flat washer, with a 1 111 6-inch hole, and at least 1 11 2-inch out- side diameter (4) Three 11 4 x 20 thumbscrews 1- inch long and one 11 2-inch long (5) 3 11 2 linear feet (42 inches) ... respirator (14 ) 11 8-inch x 11 2-inch steel flat bar 5-foot long (15 ) 1- inch pipe plug (16 ) Welding rod or brazing rod, flux, and a small brass cleaning brush (17...

Ngày tải lên: 08/08/2014, 17:20

... 11 8 x 1 112 x 1 112 -inch steel angles, 1 112 -inch long (10 ) Four 11 8 x 1 112 x 1 112 -inch steel angles, 40-inch long (12 ) Two 11 8 or 311 6-inch x 1 112 -inch flat bars, 29 314 -inch long (13 ) One ... and two rigid castor wheels (see Resources) (7) Six 11 8 x 1 112 x 1 112 -inch steel angles, 35 314 -inch long (8) Six 11 8 x 1 112 x 1 112 -inch steel...

Ngày tải lên: 08/08/2014, 17:20

... Gas Burners 8 (12 ) 911 6 -18 LH thread to 11 4 MPT outlet bushing or 318 flared fitting (13 ) Can of tappping oil (14 ) 11 8 NPT coupling (15 ) Fourteen #10 x 32 x 11 4-inch SS set screws (16 ) ... bushing) (12 ) 9 /16 -18 LH thread to 11 4 MPT Outlet Bushing (13 ) 10 -24 x 15 164" brass threaded wood insert. ( 14 ) 11 8 NPT brass coupling (15 ) Six # 10...

Ngày tải lên: 08/08/2014, 17:20

... SS machine screws and nuts (13 ) 1 112 x 314 NPT bell reducer (14 ) 1 112 NPT short nipple, 314 NPT short nipple (15 ) Three 1/ 4-20 x 1 11 2inch thumbscrews (16 ) 11 2-inch jet ejector style ... One 11 2 x 10 -inch round kiln shelf and one 11 2 x 6-inch round kiln shelf (10 ) One standard door hinge (1 1) Four 10 -32 x 1 114 -inch SS machine screws...

Ngày tải lên: 08/08/2014, 17:20

... to 318 x 24-inch of allthread rod, three coupling nuts, twelve plain nuts (16 ) Is changed to 30-feet of 11 8 x 314 x 314 steel angle (17 ) 11 8-inch x 11 4-inch steel flat bar 1- foot long ( 21) ... doubt, ask before you purchase the pipe. Chapter 4, Building the 314 -inch Burner (1) 1 11 4-inch ID # 316 SS tube 2 11 2-inches long; you can use CRSS but # 316 is better. 1...

Ngày tải lên: 08/08/2014, 17:20

... "T" fitting; 11 4-inch brass elbow; 11 8-inch brass elbow; 11 4-inch x 1 112 -inch (long) brass pipe nipple; 11 4-inch x 2-inch brass nipple; 11 4-inch x 3-inch brass nip- ple; 11 4-inch x 4-inch ... nipple; 11 4-inch x 6-inch brass nipple; 318 -inch compres- sion x 11 4-inch MPT; 1 112 -inch x 314 -inch bell reducer (not drilled); 1 112 -inch x 314 -inch bell...

Ngày tải lên: 08/08/2014, 17:20

... the burner tube 1 15 Preparing the end cap 1 15 Recommended ignition port 1 16 Tuning 1 17 less forgiving 1 17 two different tips 1 17 I -inch Furnace Burner 10 5 Assembling ... 15 1 Farrier's Forge 13 9 Clamshell Forge 13 9 Constructing the burner collar 14 1 Curing and coating the forge 14 4 Installing the insulation and heat shield in the...

Ngày tải lên: 08/08/2014, 17:20