DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 2 potx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 2 potx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 2 potx

... line B[B2 extended. 4 Bisect line segment B [B2 , and draw a circle of that radius about 02. 5 Label the two intersections of the circle and B[B2 extended, A[ and A2. 6 Measure the length of the ... on it to the product to the next work station where it again stops for another operation to be per- the Atheneum Club in formed. The forces and power required...

Ngày tải lên: 08/08/2014, 12:23

93 756 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 3 pot

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 3 pot

... using the approach of equations 5 .27 and 5.18, by changing W to U and Z to S and using the definitions of the constants given in equation 5.30 in equation 5 .27 . It should be apparent that there ... respectively) on the coupler (link 3). We wish to solve for the coordinates of vectors W, Z, D, and S, which define not only the lengths of those links but also...

Ngày tải lên: 08/08/2014, 13:20

93 396 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 4 pptx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 4 pptx

... wish to solve for 004, the angular velocity of link 4, and also for the velocity of slip at the joint labeled A. In Figure 6-18 the axis of slip is shown to be tangent to the slider motion and ... is the line along which all sliding occurs between links 3 and 4. The axis of transmission is defined to be perpendicular to the axis of slip and pass thr...

Ngày tải lên: 08/08/2014, 13:20

93 395 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 5 pps

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 5 pps

... side and high dwell on the other, note that the velocity function is multivalued. There are discontinuities at these boundaries. The effect of these discontinuities is to create a portion of the ... ANGLE AND RADIUS OF CURVATURE Once the s v a j functions have been defined, the next step is to size the cam. There are two major factors which affect cam size, the p...

Ngày tải lên: 08/08/2014, 13:20

93 484 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 6 potx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 6 potx

... stage of the design to accurately determine the best sizes and shapes of the parts. We must estimate the masses of the links and other parts of the design in order to make a first pass at the calculation. ... golf club. In the case of our mallet example, a center of percussion at the head corresponds to a center of rotation near the end of th...

Ngày tải lên: 08/08/2014, 13:20

93 381 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 7 potx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 7 potx

... us to size the motor to deliver the average torque rather than the peak torque. One convenient and rel- atively inexpensive means to this end is the addition of a flywheel to the system. TORQUE ... the driver (motor) and stored temporarily in the moving links, and the negative pulses of torque as energy at- tempting to return from the links to the dri...

Ngày tải lên: 08/08/2014, 13:20

93 457 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 8 ppsx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 8 ppsx

... the driver (motor) and stored temporarily in the moving links, and the negative pulses of torque as energy at- tempting to return from the links to the driver. Unfortunately most motors are designed to ... convert the cartesian mR products in equations 12. 8c and 12. 8d to polar coordinates in order to find the magnitude and angle of the counterweight&apo...

Ngày tải lên: 08/08/2014, 13:20

93 391 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 9 docx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 9 docx

... one to the other, in order to stagger the mo- tions of the pistons in time. It should be apparent from the discussion of shaking forces and balancing in the previous chapter that we would like to ... the program. These are noted in the text. The student is encouraged to investigate these ex- amples with program ENGINE in order to develop an understanding of...

Ngày tải lên: 08/08/2014, 13:20

93 461 0
DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 10 docx

DESIGN OF MACHINERYAN INTRODUCTION TO THE SYNTHESIS AND ANALYSIS OF MECHANISMS AND MACHINES phần 10 docx

... as the magnitude and angle of the vector are displayed. The programs also allow alternate presentations of polar plots, showing just the vec- tors, just the envelope of the path of the vector ... change any of the linkage parameters on the Animate screen and then recalculate the results there with the Recalc button. The Done button on either the Input o...

Ngày tải lên: 08/08/2014, 13:20

87 365 0
Introduction of An Introduction to the Philosophy of Mind

Introduction of An Introduction to the Philosophy of Mind

... experience and the relationship between mental and physical states. Then, in chapters 3 and 4, I move on to discuss certain gen- eral theories of the nature of mental states and some attempts to explain ... philosophical analysis of the concept of seeing: but each will have more credibility to the extent that it is consistent with the other. METAPHYSICS AND...

Ngày tải lên: 01/11/2013, 07:20

7 533 0
w