Tutorial Material for Pro/ENGINEER Wildfire 2 0 pdf

... Figure 25 MAE 24 4 : Dynamics and Strength Laboratory Fall 20 05 Tutorial Material for Pro/ENGINEER Wildfire 2. 0 With Integrated Pro/MECHANICA Tutorial ... L- Shaped Rod MAE 24 4 : Dynamics / Strength Laboratory Fall 20 05 Chuanyu “tony” Feng 20 20 . Click menu: Run Æ Start in the Analysis and Design Studies window(F...

Ngày tải lên: 08/08/2014, 12:22

... budgeted $ 500 ,00 0 for the networking equipment and another $ 10, 000 /month for the WAN charges including a faster Internet connection. They believe that 25 6Kbps speeds will be adequate to the 6 40- 861 ... systems. They have budgeted $ 500 ,00 0 for the networking equipment and another $ 10, 000 /month for the WAN charges including a faster Internet connection. They believe...

Ngày tải lên: 21/12/2013, 05:18

... 1 ME-4 30 Introduction to Computer Aided Design ARM BRACKET - Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata In a system window, create a new directory called ME-4 30 (e.g. H:\PTC_Working_Dir\ME-4 30) . ... Horizontal: 10 Vertical: 12. 5 This placement references can be verified by clicking the Placement tab. Click . 6...

Ngày tải lên: 27/10/2013, 17:15

... Double click PITCH1 .00 , and change the value 0. 5. Pick the Regenerate icon . Pick the trajectory. 20 4 Sketch a circle with diameter 0 .25 centered on the ... The revolved angle is 30 degrees. RIGHT datum plane 1 ME-4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Helical Extension Spring Pro/ENGINEER Wildfire 2. 0...

Ngày tải lên: 06/11/2013, 00:15

... GRAPH menu and OK from the dialog box. ME-4 30 INTRODUCTION TO COMPUTER AIDED DESIGN Variable Pitch Conical Spring Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata START CREATING A NEW ... revolved angle to be 1 80. and click the button to finish. CREATE A REVOLVED PROTRUSION AT THE TOP PART OF SPRING Repeat the same procedure as shown above for 1 80 revolved p...

Ngày tải lên: 06/11/2013, 00:15

... select appropriate dimensions as shown below – The HEIGHT distance 3 .00 0; the overall WIDTH 4 .00 0 and bottom RADIUS 8 .00 0 of balancing body. The three dimensions are highlighted in red. ... Close. 27 17 The conclusions that can be drawn from the graphs: • The shoulder distance is greater than 0 .25 for the entire range of height values (2 – 3 ....

Ngày tải lên: 12/12/2013, 12:15

... create a 45º x 0. 02 in. chamfer on the edges shown below. Second chamfer: 45º x 0. 02 Second chamfer: 45º x 0. 02 10 In the dashboard, click the Remove Material icon . ... of decimal places to 4. Change the Nominal Value to 1 . 20 20. Change the Upper tolerance to 0. 000 6 and the Lower tolerance to 0. Select OK from the dialog box. ......

Ngày tải lên: 12/12/2013, 12:15

... 21 Click , and then pick to complete the sweep. 1 ME-4 30 Introduction to Computer Aided Design TRAY - Pro/ENGINEER Wildfire 2. 0 Dr. Herli Surjanhata ... modify the dimension as shown. 5 Click . Type in 12 for the depth of extrusion. Click . 20 Select Traj. Tangnt Chain Pick the out...

Ngày tải lên: 12/12/2013, 12:15

... "VALUES('Amaretto_decaf', 49, 10. 99, 0, 0) "); stmt.addBatch("INSERT INTO COFFEES" + "VALUES('Hazelnut_decaf', 49, 10. 99, 0, 0) "); int [] updateCounts = ... uprs.deleteRow(); Scrollable ResultSet  Với phiên bản 1 .0, ResultSet chỉ có thể duyệt theo 1 chiều là forward  Với phiên bản 2. 0, ResultSet có thể duyệt cả chiều forwar...

Ngày tải lên: 16/12/2013, 13:15

... thế, lớp DataSet trong ADO.NET 2. 0 hỗ trợ cả XML và Định dạng tuần tự hóa nhị phân. Ví dụ sau sẽ chứng mình điều này: BinaryFormatter binaryFormatter = new BinaryFormatter(); FileStream fileStream ... empDataSet.RemotingFormat = SerializationFormat.Binary; //Serialize the employee Data Set instance as binary. In order to serialize the //same instance as XML, specify Serializat...

Ngày tải lên: 22/12/2013, 22:16