Airframes and systems - part 2 ppt
Advanced Microwave Circuits and Systems Part 2 ppt
... dedicated to 3-5 GHz or 6-1 0GHz bands -3 0 -2 5 -2 0 -1 5 -1 0 -5 0 5 10 15 1 2 3 4 5 6 7 8 Frequenc y ( GHz ) S 1 1 & S 2 1 ( d B ) S11 S21 -2 5 -2 0 -1 5 -1 0 -5 0 5 10 15 2, 5 5,5 8,5 11,5 Frequency ... pre- AdvancedMicrowaveCircuits and Systems2 6 1 n+1 2n-port 2 n n +2 2n 3 4 n − 1 2n − 1 n+3 S, T, S n+4 S′, S′ 1′ 2 3′ 4′ 5′ 6...
Ngày tải lên: 21/06/2014, 06:20
Expert Systems for Human Materials and Automation Part 2 ppt
... 0,355 – 0,500 Fm +2 427 dm +2 271 0 ,21 2 – 0,355 Fm+1 28 3 dm+1 127 0,100 – 0 ,21 2 Fm 156 dm 0 0,050 –0,100 Fm-1 75 dm-1 81 < 0,050 Fm -2 25 dm -2 131 Table 3. Distribution of particles in the ... 6.01 5. 72 Kleptose® Batch 774639 5.58 8.46 5.08 6.81 10.00 4.95 3.51 6.50 0.00 8. 12 3.60 1.90 7. 02 7.30 4.98 4.06 2. 75 0.58 5.38 5. 12 Kollindon® VA64 Batch 2 8 -2...
Ngày tải lên: 19/06/2014, 10:20
MIMO Systems Theory and Applications Part 2 ppt
... becomes the 2l order Hadamard matrix. CC C −C and C 2 l = C 2 ⊗C 2 l−1 (116) where ⊗ is the Kronecker product and C 2 l−1 ,2 l is expressed as : C 2 l = C 2 l−1 C 2 l−1 C 2 l−1 −C 2 l−1 (117) Collaborative ... Diversity and Antenna Selection MIMO Systems, Theory and Applications 58 and has better error-rate performance and higher diversity gains tha...
Ngày tải lên: 20/06/2014, 04:20
Tài liệu Ielts preparationg and practice rading and writing part 2 pptx
Ngày tải lên: 14/12/2013, 13:15
Tài liệu Modules and Ports part 2 pptx
... top-level module Top. The diagram for the input/output ports is shown in Figure 4-3 . Figure 4-3 . I/O Ports for Top and Full Adder Notice that in the above figure, the module Top is a top-level ... ports a, b, and c_in and produces an output on ports sum and c_out. Thus, module fulladd4 performs an addition for its environment. The module Top is a top-level module in the...
Ngày tải lên: 15/12/2013, 03:15
Tài liệu Timing and Delay part 2 ppt
... //Delays are specified in order //for transitions 0-& gt;1, 1-& gt;0, 0-& gt;z, z->1, 1-& gt;z, z->0 // 0-& gt;x, x->1, 1-& gt;x, x->0, x->z, z->x. //Order must be followed strictly. specparam ... constants For the example in Figure 1 0-3 , we can write the module M with pin-to-pin delays, using specify blocks as follows: Example 1 0-3 Pin-to-Pin Del...
Ngày tải lên: 15/12/2013, 03:15
Tài liệu Project Planning and Control Part 2 pptx
... nodes in band 1 would be numbered 101, 1 02, 103, etc., while the nodes in band 2 are numbered 20 1, 20 2, 20 3, etc. Figure 21 .1 would lend itself to this type of numbering. Coordinates This method ... and one at the end (Figure 11.1). Thus events 1 and 2 in the figure show the start and finish of activity A. The arrow head indicates that 1 comes before 2, i.e. the operation...
Ngày tải lên: 26/01/2014, 11:20