tài liệu hướng dẫn sử dụng biến tần danfoss phần 8 doc

... = value for use in communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 78 VLT ® 280 0 Series Programming Logic or [3] Dig. input Ser. port Function 0 ... Protocol see MG91C1XX. 580 - 582 Defined parameters (DEFINED PNU’S) Value: Read only Function: The three parameters hold a list of all the parameters that are defined in the VLT 280 0. It i...

Ngày tải lên: 08/08/2014, 03:20

... communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 39 VLT ® 280 0 Series Programming Select Special motor mode [8] , if a special V/Hz setting is needed that ... serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 37 VLT ® 280 0 Series Further information is available on serial communication in the VLT 280 0 Desi...

Ngày tải lên: 08/08/2014, 03:20

... = value for use in communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 48 VLT ® 280 0 Series 120 Start delay (START DELAY) Value: 0.0 - 10.0 sec. ✭ 0.0 ... = value for use in communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 49 VLT ® 280 0 Series Description of choice: Select No protection [0...

Ngày tải lên: 08/08/2014, 03:20

... INVERSE) [6] [6] [6] [6] [6] Start (START) ✭[7] [7] [7] [7] [7] Pulse start (LATCHED START) [8] [8] [8] [8] [8] Reversing (REVERSING) [9] ✭[9] [9] [9] [9] Reversing and start (START REVERSING) [10] ... Outputs D DD Di ii ig gg gi ii it tt ta aa al ll li ii in nn np pp pu uu ut tt ts ss sT TT Te ee er rr rm mm m. .n nn no oo o. .1 11 18 88 8 1 11 1 1 11 19 99 9 1 11 1 2 22 27 77 72 22...

Ngày tải lên: 08/08/2014, 03:20

... = value for use in communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 68 VLT ® 280 0 Series Description of choice: The factory setting is 10 ms. This ... value for use in communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 65 VLT ® 280 0 Series 4 18 Speed PID integral time (SPEED INT. TIME) V...

Ngày tải lên: 08/08/2014, 03:20

... locked via parameter 0 18. Alarm/warning limits: Without brake With brake Without brake With brake VLT 280 0 1 / 3 x 200 - 240 V [VDC] 1 / 3 x 200 - 240 V [VDC] 3x 380 - 480 V [VDC] 3 x 380 - 480 V [VDC] Undervoltage ... the intermediate circuit voltage divided by 1.35. MG. 28. A7.22 - VLT is a registered Danfoss trademark 88 VLT ® 280 0 Series All about VLT 280 0 WARNING/ALARM 12: Cur...

Ngày tải lên: 08/08/2014, 03:20

... dimensions of VLT 284 0 (5 HP) 200-240 Volt and VLT 285 5- 287 5 (7 - 10HP) 380 - 480 Volt. All dimensions are in inches. VLT 284 0 200-240 Volt VLT 285 5- 287 5 380 - 480 Volt VLT 288 0 -82 380 - 480 V MG. 28. A7.22 - ... dimensions of VLT 280 3- 281 5 (1/2 - 2 HP) 200-240 Volts and VLT 280 5- 281 5 (3/4 - 2 HP) 380 - 480 Volts. All dimensions are in inches. VLT 280 3- 281 5 200-240 Volt VLT...

Ngày tải lên: 08/08/2014, 03:20

... and 4 are not applied. MG. 28. A7.22 - VLT is a registered Danfoss trademark 18 VLT ® 280 0 Series Installation VLT 284 0 200-240 V, 285 5- 287 5 380 - 480 V VLT 288 0- 288 2 380 - 480 V Please note, that the ... connected. MG. 28. A7.22 - VLT is a registered Danfoss trademark 19 VLT ® 280 0 Series ■ Electrical installation VLT 280 3- 281 5 200-240 V, 280 5- 281 5 380 - 480 V VLT 282...

Ngày tải lên: 08/08/2014, 03:20

... shows that in parameter 1 28, Motor thermal protection, the second [2] selection is active, Thermistor trip. MG. 28. A7.22 - VLT is a registered Danfoss trademark 22 VLT ® 280 0 Series Installation Programming ... = value for use in communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 28 VLT ® 280 0 Series ■ Connection examples ■ Start/stop...

Ngày tải lên: 08/08/2014, 03:20

... 2 22 28 88 80 00 03 33 32 22 28 88 80 00 05 55 52 22 28 88 80 00 07 77 72 22 28 88 81 11 11 11 12 22 28 88 81 11 15 55 52 22 28 88 82 22 22 22 22 22 28 88 84 44 40 00 0 Output current I INV. [A] 2.2 3.2 4.2 6.0 6 .8 9.6 ... x 220/230/240 V ±10% Supply voltage VLT 280 3- 284 0 200-240 V 3 x 200/2 08/ 220/230/240 V ±10% Supply voltage VLT 280 5- 288 2 380 - 480 V 3 x 380 /...

Ngày tải lên: 08/08/2014, 03:20