PSIM User Manual phần 5 pot

... only) I RESETI V d v ctrl v o Gs () sT= Transfer Function Blocks PSIM User Manual 3 -5 3.1 .5 Built-in Filter Blocks Four second-order filters are provided as built-in modules in PSIM. The transfer function of these filters ... Components 3-8 PSIM User Manual Attributes (for EXP and POWER): For the exponential function block EXP, the output is defined as: : For example, if k...

Ngày tải lên: 08/08/2014, 03:20

... windings TF_IDEAL Np Ns TF_IDEAL_1 Np Ns Lp Ls Lm Ideal Rp Rs Np:Ns Secondary Primary Switches PSIM User Manual 2-13 The gating pattern has 6 switching points (3 pulses). The corresponding switching angles are 35 o , 92 o , 1 75 o , 187 o , 3 45 o , and 357 o , respectively. If ... following: 6 35. 92. 1 75. 187. 3 45. 357 . 2.2.6 Single-Phase Switch Modules Built-in single-...

Ngày tải lên: 08/08/2014, 03:20

... Power Circuit Components 2-22 PSIM User Manual 2 .5 Other Elements 2 .5. 1 Operational Amplifier An ideal operational amplifier (op. amp.) is modelled using the PSIM power circuit ele- ments, as ... p_1 p_2 s_1 s_2 s_6 TF_1F TF_1F_3W TF_1F_5W TF_1F_7W p s t p p p s s_1 s_4 s_1 s_6 s_2 sp TF_1F_1 TF_1F_5W _1 p_1 p_2 s_1 s_3 Chapter 2: Power Circuit Components 2-28 PSIM User...

Ngày tải lên: 08/08/2014, 03:20

... V o,min = -5, V o,min = 5, and V in = 3.2, then: V ox = -5 + (3.2 - 0) * (5 - ( 05) ) / (10 - 0) = -1.8 ∆ V = (5 - ( -5) ) / (2 4 - 1) = 0.66667 The value -1.8 is between -2.33332 and -1.666 65. Therefore, ... 0 0 0.2 0.33 0.11 0.22 0.33 0 0.3 0.44 0.11 0.22 0.33 0.44 0.4 0 .55 0 .55 0.22 0.33 0.44 C_BUFFER Logic Components PSIM User Manual 3-19 Attributes: Example: In the...

Ngày tải lên: 08/08/2014, 03:20

... time and value can be separated by either a comma (such as (1.2m ,5. 5)) or a space (such as (1.2m 5. 5)), or both (such as (1.2m, 5. 5)). Example: The following is a non-periodic piecewise linear ... Module PSIM User Manual 3-39 schematic file. In this example, we assume that the netlist is located in the directory “C: \PSIM6 .0”. The netlist file name and path will be “C: \PSIM6...

Ngày tải lên: 08/08/2014, 03:20

... Components 4-18 PSIM User Manual 14 7.821098 72.27710 80.72 750 99.27 251 107.7229 172.1789 180. 187.8211 252 .2771 260.72 75 279.27 25 287.7229 352 .1789 360. 14 7.902047 72.44823 80.66083 99.33917 107 .55 18 172.0979 ... 172.0979 180. 187.9021 252 .4482 260.6608 279.3392 287 .55 18 352 .0980 360. 14 10.186691 87.242 25 88. 758 61 91.24139 92. 757 75 169.8133 180. 190.1867 267.242...

Ngày tải lên: 08/08/2014, 03:20

... Design 6-12 PSIM User Manual Simulation Issues PSIM User Manual 8-9 Chapter 8: Error/Warning Messages and General Simulation Issues 8.1 Simulation Issues 8.1.1 Time Step Selection PSIM uses ... -0.289262E-18 0.6 156 18E+00 0.100000E+01 0.3000000E-04 0.000000E+00 -0 .57 6406E-18 0.923416E+00 0.100000E+01 0.4000000E-04 0.000000E+00 -0.86 058 5E-18 0.123120E+01 0.100000E+01...

Ngày tải lên: 08/08/2014, 03:20

... nroff(1), refer(1), tbl(1), troff(1), vgrind(1), whatis(1), catman(1M), attributes (5) , environ (5) , eqnchar (5) , man (5) , sgml (5) The -f and -k options use the windex database, which is created by catman(1M). The ... standard manual page directory subtree /usr/share/man/man?/* unformatted nroff manual entries /usr/share/man/sman?/* unformatted SGML manual entries man(1) Referring...

Ngày tải lên: 24/07/2014, 02:20

... section of http://www.symbian.com • User Interface Design Guidelines, at http://brew.qualcomm.com • Palm OS ® User Interface Guidelines, at http://www.palmos.com 5. 5.2 Standards Organizations Standards ... messages, or anything that may find the user viewing more than one of the set. Users exhibiting the first behavior pick an item from the list, view the item, 116 MOBILE USER INTER...

Ngày tải lên: 07/08/2014, 21:20

... Blocks 4-22 Chapter 5 Analysis Specification 5. 1 Transient Analysis 5- 1 5. 2 AC Analysis 5- 2 5. 3 Parameter Sweep 5- 6 Component Parameter Specification and Format PSIM User Manual 1 -5 TAN tangent function ATAN ... following ways: 12 .5 12.5k 12.5Ohm 12.5kOhm 25. /2.Ohm R1+R2 R1*0 .5+ (Vo+0.7)/Io where R1, R2, Vo, and Io are symbols defined either in a parameter file (s...

Ngày tải lên: 08/08/2014, 03:20