biến tần delta phần 9 docx

... Carrier Frequency (kHz) 1-15 Single/3-phase 3-phase Rated Input Current (A) 4 .9/ 1 .9 6.5/2.7 9. 5/4 .9 15.7 /9 24/15 20.6 Rated Voltage/Frequency Single/3-phase 200-240 V, 50/60Hz 3-phase ... I (A) Bussmann P/N VFD002EL11A 6.4 1.6 15 JJN-15 VFD002EL21A 4 .9 1.6 10 JJN-10 VFD002EL23A 1 .9 1.6 5 JJN-6 VFD004EL11A 9 2.5 20 JJN-20 VFD004EL21A 6.5 2.5 15 JJN-15 VFD004EL23...

Ngày tải lên: 07/08/2014, 23:20

... will disappear. 07.13 Input Debouncing Time of the PTC Protection Unit: 2ms Settings 0 ~99 99 (is 0- 199 98ms) Factory Setting: 100  This parameter is to delay the signals on PTC analog input terminals. ... +1x2 +1x2 542 =32+16+4 Setting 04. 09 =52 NOTE: 2 =16384 2 =8 192 2 =4 096 2 =2048 2 =1024 2 =512 2 =256 2 =128 2 =64 2 =32 2 =16 2 =8 2 =4 2 =2 2 =1 14 13 12 11 10 98 765 4321 0...

Ngày tải lên: 07/08/2014, 23:20

... [2.26] 59. 7 [2.35] 3.6 [0.14] 72.2 [2.84] 34.8 [1.37] AD DH ADDL SPNET CME-PB01 UNIT: mm(inch) B.8.3.3 Parameters Settings in VFD-EL VFD-EL Baud Rate 96 00 Pr. 09. 01=1 RTU 8, N, 2 Pr. 09. 03=3 ... Accessories| Revision June 2007, 0ELE, V1.00 B- 19 B.8.2.3 Specifications Power supply: 16-30VDC, 750mW Communication: Modbus in ASCII format, protocol: 96 00, 7, N, 2 LonTalk: fre...

Ngày tải lên: 07/08/2014, 23:20

... (POWER UPS) Number of times 0 -99 99 604 Number of overtemperatures (OVER TEMPS) Number of times 0 -99 99 605 Number of overvoltages (OVER VOLTS) Number of times 0 -99 99 Function: These parameters ... choice: Read out as one value. 617 Fault log: Value (F.LOG: VALUE) Value: [Index 1 - 10] Value: 0 - 99 99 Function: In this parameter it is possible to see at which value a trip occurred....

Ngày tải lên: 08/08/2014, 03:20

... AWG. (3.3- 0.8mm 2 ) Copper only, 75 o C R/L1, S/L2, T/L3 U/T1, V/T2, W/T3 B +, -, 16.3- 19. 3kgf-cm (14-17in- lbf) 8-18 AWG. (8.4- 0.8mm 2 ) Copper only, 75 o C NOTE Frame A: VFD002EL11A/21A/23A, ... the operation direction is to set by the communication parameters. Please refer to the group 9 for details.  When it needs to install the filter at the output side of terminal...

Ngày tải lên: 07/08/2014, 23:20

... 00.06 Software Version Read-only #.## 00.07 Reserved 00.08 Password Input 0 to 99 99 0 00. 09 Password Set 0 to 99 99 0 00.10 Reserved 00.11 Reserved 00.12 50Hz Base Voltage Selection 0: 230V/400V ... 03.04 Analog Output Gain 1 to 200% 100 03.05 Terminal Count Value 0 to 99 99 0 03.06 Preliminary Count Value 0 to 99 99 0 0: Terminal count value attained, no EF...

Ngày tải lên: 07/08/2014, 23:20

... minimum output frequency (Pr.01.05) 0 10.18 PID Control Detection Signal Reference 1.0 to 99 .9 99. 9 Chapter 4 Parameters| 4-32 Revision June 2007, 0ELE, V1.00 01.08 Output Frequency Lower ... Unit: 1 Settings 0 to 99 99 Factory Setting: 0 Display 0~2 (times of wrong password)  The function of this parameter is to input the password that is set in Pr.00. 09. Input the c...

Ngày tải lên: 07/08/2014, 23:20