biến tần delta phần 8 doc

... connect correctly and no noise is present AC motor drive has malfunction. Please contact DELTA. 5 .8 Phase Loss (PHL) Phase loss No No Yes Yes Check wiring at R, S and T terminals Correct ... misoperation due to noise. Please contact DELTA. Change defective potentiometer No Chapter 4 Parameters| 4-104 Revision June 2007, 0ELE, V1.00 10. 18 PID Control Detection Signal Referenc...

Ngày tải lên: 07/08/2014, 23:20

... +1x2 542 =32+16+4 Setting 04.09 =52 NOTE: 2 =16 384 2 =81 92 2 =4096 2 =20 48 2 =1024 2 =512 2 =256 2 =1 28 2 =64 2 =32 2 =16 2 =8 2 =4 2 =2 2 =1 14 13 12 11 10 987 65 4321 0  This parameter is to delay ... table. 8 Jog Operation Control Parameter value 08 programs one of the Multi-function Input Terminals MI3 ∼ MI6 (Pr.04.05~Pr.04. 08) for Jog control. NOTE: Programming for...

Ngày tải lên: 07/08/2014, 23:20

... 1 BR200W 150 1 140 80 Ω 2 1.5 VFD015EL 21A/23A 0 .84 9 300W 85 Ω BUE- 20015 1 - 125 80 Ω 3 2.2 VFD022EL 21A/23A 1.262 * * * 230V Series 5 3.7 VFD037EL 23A 2. 080 * * * Appendix B ... 5% impedance 0.2 1/4 4 4 9 12 0.4 1/2 6 6 6.5 9 0.75 1 8 12 3 5 1.5 2 8 12 1.5 3 2.2 3 12 18 1.25 2.5 3.7 5 18 27 0 .8 1.5 Chapter 6 Fault Code Information and Maintena...

Ngày tải lên: 07/08/2014, 23:20

... FTT-10A 78 Kbps. LonTalk terminal: 4-pin terminals, wire gauge: 28- 12 AWG, wire strip length: 7-8mm RS- 485 port: 8 pins with RJ-45 B .8. 2.4 Wiring SP CME-LW01 Power LED SP LED Service LED Service ... B .8. 3 Profibus Communication Module (CME-PD01) B .8. 3.1 Panel Appearance 1: Reserved 2: EV 5: SG+ 6: Reserved 7: Reserved 8: Reserved 3: GND 4: SG- Profibus-DP Interface...

Ngày tải lên: 07/08/2014, 23:20

... Protocol see MG91C1XX. 580 - 582 Defined parameters (DEFINED PNU’S) Value: Read only Function: The three parameters hold a list of all the parameters that are defined in the VLT 280 0. It is possible ... = value for use in communication via serial communication port MG. 28. A7.22 - VLT is a registered Danfoss trademark 78 VLT ® 280 0 Series Programming Logic or [3] Dig. input Ser. port Fu...

Ngày tải lên: 08/08/2014, 03:20

... 14.2- 16.3kgf-cm (12-14in- lbf) 12- 18 AWG. (3.3- 0.8mm 2 ) Copper only, 75 o C R/L1, S/L2, T/L3 U/T1, V/T2, W/T3 B +, -, 16.3- 19.3kgf-cm (14-17in- lbf) 8- 18 AWG. (8. 4- 0.8mm 2 ) Copper only, 75 o C NOTE ... Common Factory setting AVI ACI Factory setting: AVI Mode - RS- 485 Serial interface 1: Reserved 2: EV 5: SG+ 6: Reserved 7: Reserved 8: Reserved 3: GND 4: SG- 8...

Ngày tải lên: 07/08/2014, 23:20

... 08. 08 Current Limit for Speed Search 30 to 200% 150 08. 09 Skip Frequency 1 Upper Limit 0.00 to 600.0 Hz 0.00 08. 10 Skip Frequency 1 Lower Limit 0.00 to 600.0 Hz 0.00 08. 11 ... Setting Custome r 08. 00 DC Braking Current Level 0 to 100% 0 08. 01 DC Braking Time during Start-Up 0.0 to 60.0 sec 0.0 08. 02 DC Braking Time during Stopping 0.0 to 60.0...

Ngày tải lên: 07/08/2014, 23:20

... 04.05~04. 08 Chapter 4 Parameters| 4- 18 Revision June 2007, 0ELE, V1.00 Parameter Explanation Settings Factory Setting Customer 6: 8, N,1 (Modbus, RTU) 7: 8, E,2 (Modbus, RTU) 8: 8, O,2 (Modbus, ... Password END Displays 0 when entering correct password into Pr.00. 08. 00.09 00. 08 00. 08 Displays 0 when enterin g correct password into Pr.00. 08. Correct Password END...

Ngày tải lên: 07/08/2014, 23:20