biến tần delta phần 3 pptx

... 26: W-phase error (cF3.2) 27: DCBUS error (cF3 .3) 28: IGBT Overheat (cF3.4) 29: Reserved 30 : Reserved 31 : Reserved 32 : ACI signal error (AErr) 33 : Reserved 34 : Motor PTC overheat ... drive stops 03. 08 Fan Control 3: Fan ON when preliminary heatsink temperature attained 0 03. 09 Reserved 03. 10 Reserved 03. 11 Brake Release Frequency 0.00 to 20.00Hz...

Ngày tải lên: 07/08/2014, 23:20

... V1.00 AVI A CI/AVI ACM +10V 5K 3 2 1 Figure 2 for models of VFD-EL Series V FD002EL23A, VFD004EL23A/43A, VFD007EL23A/43A, VFD015EL23A/43A, VFD022EL23A/43A, VFD 037 EL23A/43A Power supply +10V 3mA Master Frequency 0 ... Frame A: VFD002EL11A/21A/23A, VFD004EL11A/21A/23A/43A, VFD007EL21A/23A/43A, VFD015EL23A/43A Frame B: VFD007EL11A, VFD015EL21A, VFD022EL21A/23A/43A, VFD 037 EL23A/43A...

Ngày tải lên: 07/08/2014, 23:20

... (50Hz)! Tải mômen biến thiên (Variable Torque – VT) Tải cơ 29 57 Chức năng tốc ñộ ñặt trước Các chức năng biến tần (tiếp…) Thực hành 58 Chức năng chạy JOG Các chức năng biến tần (tiếp…) 23 45 f (Hz) L n P FrS L: ... khởi ñộng ñược, hoặc dòng khởi ñộng > 150% quá 1 phút, biến tần sẽ “trip”. Biến tần báo lỗi: OLF (Over current (Torque limit - ATV31, ATV58, ATV68, ATV71 ñ...

Ngày tải lên: 07/08/2014, 23:20

... Pr.01.18 or Pr.01.12 + Pr.01.18 3 1 2 4 1 3 4 2 1 2 3 4 Disable S curve Enable S curve A cceleration/deceleration Characteristics Chapter 4 Parameters| 4 -30 Revision June 2007, 0ELE, V1.00 ... conveyor belt runs at 13. 6m/s at motor speed 60Hz. K = 13. 6/60 = 0.22 (0.226667 rounded to 1 decimal), therefore Pr.00.05=0.2 With Frequency command 35 Hz, display shows U and 35 *0.2=7....

Ngày tải lên: 07/08/2014, 23:20

... Pr. 03. 00is set to 21. Refer to the following example for details. Example: 1. Case 1: Pr. 03. 12 ≥ Pr. 03. 11 2. Case 2: Pr. 03. 12 ≤ Pr. 03. 11 Case 1: Pr. 03. 12 Case 2: Pr. 03. 12 Pr. 03. 11 Frequency Output Time Run/Stop Case ... =20.0% Bias adjustment Pr.04.01 =0 Positive bias Pr.04.02 = 83. 3% Input gain Pr.04. 03 =0 No negative bias command Gain:(10V/(10V+2V))*100%= 83....

Ngày tải lên: 07/08/2014, 23:20

... 133 0Ω, the voltage between +10V-ACM is 10.5V and resistor-divider R1 is 4.4kΩ. Refer to following calculation for Pr.07.14 setting. 133 0//47000=( 133 0*47000)/( 133 0+47000)=12 93. 4 10.5*12 93. 4/(4400+12 93. 4)=2 .38 (V) ... failure (HPF3) 23 OC Hardware protection failure (HPF4) 24 U-phase error (cF3.0) 25 V-phase error (cF3.1) 26 W-phase error (cF3.2) 27 DCBUS error (cF3...

Ngày tải lên: 07/08/2014, 23:20

... shown as ‘64’ in ASCII, consists of ‘6’ (36 Hex) and ‘4’ (34 Hex). Character ‘0’ ‘1’ ‘2’ 3 ‘4’ ‘5’ ‘6’ ‘7’ ASCII code 30 H 31 H 32 H 33 H 34 H 35 H 36 H 37 H Chapter 4 Parameters| Revision June ... protection failure (HPF3) 23: OC Hardware protection failure (HPF4) 24: U-phase error (cF3.0) 25: V-phase error (cF3.1) 26: W-phase error (cF3.2) 27: DCBUS error (cF3 .3) Ch...

Ngày tải lên: 07/08/2014, 23:20

... (for 115V/ 230 V models) 400VDC (for 460V models) Maybe AC motor drive has malfunction. Please contact DELTA. Control circuit has malfunction or misoperation due to noise. Please contact DELTA. Yes Using ... drive rated input voltage range. 2. Check for abnormal load in motor. 3. Check for correct wiring of input power to R-S- T (for 3- phase models) without phase loss. Overload Th...

Ngày tải lên: 07/08/2014, 23:20

... VFD007EL23A 4.9 4.2 10 JJN-10 VFD007EL43A 3. 2 2.5 5 JJS-6 VFD015EL21A 15.7 7.5 30 JJN -30 VFD015EL23A 9 7.5 20 JJN-20 VFD015EL43A 4 .3 4.2 10 JJS-10 VFD022EL21A 24 11 50 JJN-50 VFD022EL23A 15 11 30 ... BR300W100, BR300W250, BR300W400, BR400W150, BR400W040 Model no. L1 L2 H D W Max. Weight (g) BR080W200 BR080W750 140 125 20 5 .3 60 160 BR300W100 BR300W250 BR300W400 2...

Ngày tải lên: 07/08/2014, 23:20