dohrmann Episode 1 Part 2 ppsx

... – 12 – [1 18 /18 ] 8.5 .20 03 9 : 12 PM Fig. 1. 13 General classification of manufacturing processes. 12 A strategic view //SYS 21 / //INTEGRAS/B&H/PRS/FINALS_07-05-03/0750654376-CH0 01. 3D – 15 – [1 18 /18 ] ... assembly 11 //SYS 21 / //INTEGRAS/B&H/PRS/FINALS_07-05-03/0750654376-CH0 01. 3D – 14 – [1 18 /18 ] 8.5 .20 03 9 : 12 PM Fig. 1. 15 General classification of joining...

Ngày tải lên: 21/07/2014, 16:21

... www.english-test.net Test 22 TOEIC Vocabulary / Word by Meaning / Test # 22 Q1 adj. prepared; set; eager; willing; quick; fast (a) ample (b) comfortable (c) ready (d) few Q2 adj. present; opposite ... www.english-test.net Test 42 TOEIC Vocabulary / Word by Meaning / Test # 42 Q1 n. tip; bonus; recompense (a) blue sky laws (b) sharp (c) gratuity (d) improvement Q2 v. to carry; to encoura...

Ngày tải lên: 21/07/2014, 22:20

... y0 w0 h1" alt=""

Ngày tải lên: 21/07/2014, 22:20

... tip of B reaches ( 1, 5). If the tail of vector A – B were set at the origin of the xy-axis, what point would its tip touch? (A) (2 ,11 ) (B) (2 ,1) (C) ( 2, 7) (D) (4 ,1) (E) (4 ,11 ) 4. . A and B are ... that it goes from a velocity of 20 m/s to a velocity of 40 m/s in 4 seconds. What is its acceleration? (A) 0 .2 m/s 2 (B) 4 m/s 2 (C) 5 m/s 2 (D) 10 m/s 2 (E) 80 m/s 2 Qu...

Ngày tải lên: 22/07/2014, 10:22

... AnsAns AnsAns Ans ww ww w erer erer er ss ss s 1. C 2. B 3. E 4. B 5. B 6. E 7. B 8. E 9. A 10 . A 11 . C 12 . D 13 . C 14 . B 15 . C 16 . D 17 . B 18 . C 19 . D 20 . E 21 . E 22 . D 23 . D 24 . C 25 . B 26 . C 27 . C 28 . C 29 . C 30. A 31. B 32. ... of . 024 5m. Stating the equations: and but an Vgd Vad VV f f 2 0 2 2 0 2 2 2 = =− = dd m/s m...

Ngày tải lên: 22/07/2014, 10:22

... B 10 . E 11 . D 12 . E 13 . C 14 . B 15 . A 16 . C 17 . C 18 . E 19 . D 20 . A 21 . D 22 . B 23 . C 24 . E 25 . D 26 . C 27 . D 28 . E 29 . E 30. B 31. C 32. A 33. D 34. A 35. D 36. C 37. A 38. D 39. E 40. C 41. ... be approximately (A) 16 .3% T and 16 .3% C. (B) 34 .1% T and 34 .1% C. (C) 34 .1% T and 16 .3% C. (D) 16 .3% T and 34 .1% C. (E) 33.4% T and 16 .2% C....

Ngày tải lên: 22/07/2014, 11:20

... 2 .10 413 4 2 .10 5353 2 .10 6570 2 .10 7786 2 .10 9000 2 .11 0 21 3 2 .11 1 425 2 .11 26 35 2 .11 3843 2 .11 5050 8.3 2 .11 625 6 2 .11 7460 2 .11 86 62 2 .11 9863 2 . 12 1063 2 . 12 22 62 2 . 12 3458 2 . 12 4654 2 . 12 5848 2 . 12 70 41 8.4 2 . 12 823 2 ... 1. 20 29 72 1. 20 59 71 1 .20 8960 1. 21 1 9 41 1. 21 4 913 1. 21 7 876 1. 22 083...

Ngày tải lên: 05/08/2014, 12:20

... sign. 25 .45 not 25 .45 25 .00 25 32 + 0 .25 not 32 + 0 .25 − 0 .10 − 0 .1 For unilateral tolerances, express the nil value as a single zero digit with no plus or minus sign. 32 0 or 32 ... example, ∅. 625 LC5 or 30 f7. 5-50 Chapter Five Eliminate unnecessary trailing zeros. 25 .1 not 25 .10 12 not 12 .0 with not with The exceptions are limit dimensions a...

Ngày tải lên: 21/07/2014, 15:20

... Displacement from MMC Allowable Position Tolerance 2. 74 0.00 0 .14 2. 76 0. 02 0 .16 2. 78 0.04 0 .18 2. 80 0.06 0 .20 2. 82 0.08 0 .22 2. 84 0 .10 0 .24 2. 86 0 . 12 0 .26 Tolerancing Optimization Strategies 3-7 The ... subcommittees, including Y14 Main Committee, Y14.3 Multiview and Sectional View Drawings, Y14.5 Dimensioning and Tolerancing, Y14 .11 Molded Part Drawings, Y14....

Ngày tải lên: 21/07/2014, 15:20