Machining and Monitoring Strategies Part 9 pot

... 253. Micro- and nano -machining of parts is a big challenge for both today and tomorrow. Machining and Monitoring Strategies  cutting edge corners – where high stresses and tem- peratures are ... dimensional sizes and scales, for: • machining of accurate and presicion parts or • equated to their respective measurement. [Source: Smith, et al., 2002] . Machining and...

Ngày tải lên: 05/08/2014, 21:20

... 24–32, June, 199 5. Cho, D-W., Lee, S.J. and Chu, C.N. e State of Machin- ing Process Monitoring Research in Korea. Int. J. Mach. Tools Manufact., Vol. 39, 1 697 –1715, 199 9. Chungchoo, C. and Saini, ... Tool and CMM Accuracy and Precision. Proc. of Int. Conf. Laser Metrology and Machine Performance, Northumbria (England), Wit Press, 3 89 402, 199 9. Smith, G.T. Monitoring...

Ngày tải lên: 05/08/2014, 21:20

... speed machining of metals – according to Salomon’s machining trials. [Source: Salomon, circa 192 0’s–30’s] . Machining and Monitoring Strategies  Figure 217. Typical ‘modular design’ and construction ... construction of machining centres, with ‘ballscrews’ and ‘tychoways’. [Courtesy of Cin- cinnati Machines] .  Chapter  9 Machining and Monitoring Strategi...

Ngày tải lên: 05/08/2014, 21:20

... rest and press against machined surface and thus, generate minute ‘gouging-eects’ in the surface. (Source: Seames, 199 0; Smith, 199 3) Machining and Monitoring Strategies  Figure 2 19. Machine ... positioning. [Source: Smith and Maxted, 199 5] .  Chapter  Figure 222. The CNC control problem of servo-lag and its aect on the associated HSM motional kinematics. Machi...

Ngày tải lên: 05/08/2014, 21:20

... G.T.] . Machining and Monitoring Strategies  Figure 225. Variax/Hexapod oers a unique and rigid design solution, with many production benets. [Cour- tesy of Giddings & Lewis] . Machining and ... ‘word-address format’ programs.*Non–modal commands are only active in that actual block. [Source, Smith et al., 199 3] Machining and Monitoring Strategies  NB e ma...

Ngày tải lên: 05/08/2014, 21:20

... 24 inches of length. is 7/24 system incorporates several Standards: CAT and BT 40- and 50-taper tooling. Machining and Monitoring Strategies  e capacity for the workpiece, or even a chuck ... coincide Machining and Monitoring Strategies  9. 5 Dynamic Balance of Toolholding Assemblies Introduc tion Balancing tools that are intended for HSM applica- tions is vita...

Ngày tải lên: 05/08/2014, 21:20

... Wyatt & Hope, 199 8] . Machining and Monitoring Strategies  Figure 233. A graph to determine high-speed cutter unbalance ‘U’ (ANSI S2. 19 198 9). Machining and Monitoring Strategies  the ... directional plane. Machining and Monitoring Strategies  Figure 234. Dynamic dual-plane (i.e. radial and axial) cutter balancing. [Courtesy of Ingersoll]. Machinin...

Ngày tải lên: 05/08/2014, 21:20

... assessment of machine tools such as machining centres, has been utilised for some of years (i.e typically: NAS Stan- dard 97 9: 196 9; ISO Standard: 10 791 -7: 199 7; Knapp, 199 7), being developed just for ... probe, these being invariably used on such machines. Machining and Monitoring Strategies  Figure 2 39. An ultra-high-speed trepanning xture and dual-plane balance...

Ngày tải lên: 05/08/2014, 21:20

... drilling and multi-axis milling operations. [Courtesy of Kistler Instru- mente AG] . Machining and Monitoring Strategies  Figure 245. The complex machining of either a sculptured, or die and mould ... machined prole. [Courtesy of Sandvik Coromant] . Machining and Monitoring Strategies  Figure 243. Technique of manufacture of the aerospace aluminium disks and t...

Ngày tải lên: 05/08/2014, 21:20

... generated pristine forms which would Machining and Monitoring Strategies  Figure 2 49. By utilising a sophisticated cutter and part simulation technique, any potential and very costly ma- chining mistakes ... [Courtesy of Sandvik Coromant] . Machining and Monitoring Strategies  Figure 248. CNT tool cutter path control while contouring sculptured surfaces – utilis-...

Ngày tải lên: 05/08/2014, 21:20