Machining and Monitoring Strategies Part 4 docx

... 24 inches of length. is 7/ 24 system incorporates several Standards: CAT and BT 40 - and 50-taper tooling. Machining and Monitoring Strategies  e capacity for the workpiece, or even a chuck ... tool- holder and the machine’s spindle was the dual-contact 7/ 24 taper system 24 . e CAT Standard incorporates this 7/ 24 taper, but also allows simultaneous contact on...

Ngày tải lên: 05/08/2014, 21:20

... positioning. [Source: Smith and Maxted, 1995] .  Chapter  Figure 222. The CNC control problem of servo-lag and its aect on the associated HSM motional kinematics. Machining and Monitoring Strategies  less ... cutting tool to rest and press against machined surface and thus, generate minute ‘gouging-eects’ in the surface. (Source: Seames, 1990; Smith, 1993) Machinin...

Ngày tải lên: 05/08/2014, 21:20

... speed machining of metals – according to Salomon’s machining trials. [Source: Salomon, circa 1920’s–30’s] . Machining and Monitoring Strategies  Figure 217. Typical ‘modular design’ and construction ... construction of machining centres, with ‘ballscrews’ and ‘tychoways’. [Courtesy of Cin- cinnati Machines] .  Chapter  9 Machining and Monitoring Strategies...

Ngày tải lên: 05/08/2014, 21:20

... G.T.] . Machining and Monitoring Strategies  Figure 225. Variax/Hexapod oers a unique and rigid design solution, with many production benets. [Cour- tesy of Giddings & Lewis] . Machining and ... allows the ‘Variax’ to move and accelerate up to ve times faster than a conventional machine tool. Machining and Monitoring Strategies  Figure 226. Robotic high-...

Ngày tải lên: 05/08/2014, 21:20

... directional plane. Machining and Monitoring Strategies  Figure 2 34. Dynamic dual-plane (i.e. radial and axial) cutter balancing. [Courtesy of Ingersoll]. Machining and Monitoring Strategies  in ... Wyatt & Hope, 1998] . Machining and Monitoring Strategies  Figure 233. A graph to determine high-speed cutter unbalance ‘U’ (ANSI S2.19–1989). Machining...

Ngày tải lên: 05/08/2014, 21:20

... 2003] . Machining and Monitoring Strategies  Figure 237. An ultra-high-speed turning operation undertaken on a vertical machining centre. [Source: Smith, Littlefair, Wyatt & Berry, 2003] . Machining ... disk – to be milled by circular interpolation. In Fig. 243 a, the last machinable disk has been located and clamped and the whole mandrel -and- disk assem- bly was nea...

Ngày tải lên: 05/08/2014, 21:20

... 245 . The complex machining of either a sculptured, or die and mould surfaces, will usually necessitate both multifarious and sophisticated programming techniques . Machining and Monitoring Strategies ... dynamom- Figure 244 . A high-speed rotating cutting force dynamometer, employed during drilling and multi-axis milling operations. [Courtesy of Kistler Instru- mente AG]...

Ngày tải lên: 05/08/2014, 21:20

... generated pristine forms which would Machining and Monitoring Strategies  Figure 249 . By utilising a sophisticated cutter and part simulation technique, any potential and very costly ma- chining mistakes ... composite-lled cavities. (Source: Kennedy, 20 04) Machining and Monitoring Strategies  having the necessary surface texture. In the case of hard -part turn...

Ngày tải lên: 05/08/2014, 21:20

... 253. Micro- and nano -machining of parts is a big challenge for both today and tomorrow. Machining and Monitoring Strategies  cutting edge corners – where high stresses and tem- peratures are ...  Figure 2 54. Relative dimensional sizes and scales, for: • machining of accurate and presicion parts or • equated to their respective measurement. [Source: Smith, et al., 20...

Ngày tải lên: 05/08/2014, 21:20

... [Source: Lamb & Gull, 1999] . Machining and Monitoring Strategies  Figure 255. Some typical micro-tooling: drills and boring tools. Machining and Monitoring Strategies  sizes of 25 µm. ... uncertainty, u c  = instru- ment/equipment uncertainty. (Source: Figliola and Beasley et al., 2000) Machining and Monitoring Strategies  of an equivalent cast iron...

Ngày tải lên: 05/08/2014, 21:20