Machining and Monitoring Strategies Part 3 doc
Machining and Monitoring Strategies Part 3 doc
... G.T.]
.
Machining and Monitoring Strategies
Figure 225. Variax/Hexapod oers a unique and rigid design solution, with many production benets. [Cour-
tesy of Giddings & Lewis]
.
Machining and ... allows the ‘Variax’ to move and
accelerate up to ve times faster than a conventional machine
tool.
Machining and Monitoring Strategies
Figure 226. Robotic high-...
Machining and Monitoring Strategies Part 2 docx
... cutting tool to rest and press against
machined surface and thus, generate minute ‘gouging-eects’
in the surface. (Source: Seames, 1990; Smith, 19 93)
Machining and Monitoring Strategies
Figure ... positioning.
[Source: Smith and Maxted, 1995]
.
Chapter
Figure 222. The CNC control problem of servo-lag and its aect on the associated HSM motional kinematics.
Machi...
Machining and Monitoring Strategies Part 4 docx
... 24 inches of length. is 7/24 system
incorporates several Standards: CAT and BT 40- and 50-taper
tooling.
Machining and Monitoring Strategies
e capacity for the workpiece, or even a chuck ... Diashowa Tooling]
.
Machining and Monitoring Strategies
Figure 229. Thermal expansion tooling its operation and high-speed turning chuck details.
Chapter
Figure 232...
Machining and Monitoring Strategies Part 1 ppt
...
Salomon, circa 1920’s 30 ’s]
.
Machining and Monitoring Strategies
Figure 217. Typical ‘modular design’ and construction of machining centres, with ‘ballscrews’ and ‘tychoways’. [Courtesy of ... reaches a maximum value greater
than unity.’ (Figliola and Beasley et al., 2000)
Machining and Monitoring Strategies
9.1 High Speed Machining
(HSM)
Background to H...
Machining and Monitoring Strategies Part 5 pptx
...
directional plane.
Machining and Monitoring Strategies
Figure 234 . Dynamic dual-plane (i.e. radial and axial) cutter balancing. [Courtesy of Ingersoll].
Machining and Monitoring Strategies
in ...
Wyatt & Hope, 1998]
.
Machining and Monitoring Strategies
Figure 233 . A graph to determine high-speed cutter unbalance ‘U’ (ANSI S2.19–1989).
Machining...
Machining and Monitoring Strategies Part 6 ppt
... 20 03]
.
Machining and Monitoring Strategies
Figure 237 . An ultra-high-speed turning operation undertaken on a vertical machining centre. [Source: Smith, Littlefair,
Wyatt & Berry, 20 03]
.
Machining ... sheet, to nominally slightly >
30 0 mm) each one
being set 100 mm apart in height (i.e. disks: 1, 2 and 3)
and aer machining, the disks were exactly 30 0 m...
Machining and Monitoring Strategies Part 7 ppt
... drilling and multi-axis milling
operations. [Courtesy of Kistler Instru-
mente AG]
.
Machining and Monitoring Strategies
Figure 245. The complex machining of either a sculptured, or die and mould ...
machined prole. [Courtesy of Sandvik Coromant]
.
Machining and Monitoring Strategies
Figure 2 43. Technique of manufacture of the aerospace aluminium disks and...
Machining and Monitoring Strategies Part 8 pptx
... generated pristine forms which would
Machining and Monitoring Strategies
Figure 249. By utilising a sophisticated cutter and part simulation technique, any potential and very costly ma-
chining mistakes ... toughness (K
IC
)
@ 17 MN m
3/ 2
; Izod impact strength (un-notched) @ 33 .4 J.
(Source: Trent, 1984)
53 ‘Hard -part machining , today is utilised widely as both...
Machining and Monitoring Strategies Part 9 pot
... 2 53. Micro- and nano -machining of parts is a big challenge for both today and tomorrow.
Machining and Monitoring Strategies
cutting edge corners – where high stresses and tem-
peratures are ... dimensional sizes and scales, for:
• machining of accurate and presicion parts or
• equated to their respective measurement.
[Source: Smith, et al., 2002]
.
Machining and...
Machining and Monitoring Strategies Part 10 ppsx
... [Source:
Lamb & Gull, 1999]
.
Machining and Monitoring Strategies
Figure 255. Some typical micro-tooling: drills and boring tools.
Machining and Monitoring Strategies
sizes of 25 µm. ... uncertainty, u
c
= instru-
ment/equipment uncertainty. (Source: Figliola and Beasley et
al., 2000)
Machining and Monitoring Strategies
of an equivalent cast iron...
Từ khóa: