Machining and Monitoring Strategies Part 1 ppt
Machining and Monitoring Strategies Part 1 ppt
... speed machining of metals – according to Salomon’s machining trials. [Source:
Salomon, circa 19 20’s–30’s]
.
Machining and Monitoring Strategies
Figure 217 . Typical ‘modular design’ and construction ... construction of machining centres, with ‘ballscrews’ and ‘tychoways’. [Courtesy of Cin-
cinnati Machines]
.
Chapter
9
Machining and
Monitoring Strategi...
Machining and Monitoring Strategies Part 5 pptx
...
Wyatt & Hope, 19 98]
.
Machining and Monitoring Strategies
Figure 233. A graph to determine high-speed cutter unbalance ‘U’ (ANSI S2 .19 19 89).
Machining and Monitoring Strategies
the ...
directional plane.
Machining and Monitoring Strategies
Figure 234. Dynamic dual-plane (i.e. radial and axial) cutter balancing. [Courtesy of Ingersoll].
Machini...
Machining and Monitoring Strategies Part 6 ppt
... were utilised: 0.5, 1. 0 and 1. 5 mm, with a con-
stant and rapid feedrate of 30 m min
1
. Apart from cut-
ting force analysis, turned surface texture, harmonic
roundness and micro-hardness results ... assessment of
machine tools such as machining centres, has been
utilised for some of years (i.e typically: NAS Stan-
dard 979: 19 69; ISO Standard: 10 7 91- 7: 19 97; Knapp,...
Machining and Monitoring Strategies Part 7 ppt
... drilling and multi-axis milling
operations. [Courtesy of Kistler Instru-
mente AG]
.
Machining and Monitoring Strategies
Figure 245. The complex machining of either a sculptured, or die and mould ...
machined prole. [Courtesy of Sandvik Coromant]
.
Machining and Monitoring Strategies
Figure 243. Technique of manufacture of the aerospace aluminium disks and t...
Machining and Monitoring Strategies Part 8 pptx
... generated pristine forms which would
Machining and Monitoring Strategies
Figure 249. By utilising a sophisticated cutter and part simulation technique, any potential and very costly ma-
chining mistakes ... [Courtesy of Sandvik Coromant]
.
Machining and Monitoring Strategies
Figure 248. CNT tool cutter path control
while contouring sculptured surfaces – utilis-...
Machining and Monitoring Strategies Part 2 docx
... In-cut
time:
Conventional 3.86 3. 71
High-speed 1. 26 1. 50
High-speed (G 61) * 1. 16 1. 55
NB All times in minutes
* G 61 is the ‘Exact-stop’ mode of machine command and, when ac
-
tivated, the machine ... rest and press against
machined surface and thus, generate minute ‘gouging-eects’
in the surface. (Source: Seames, 19 90; Smith, 19 93)
Machining and Monitoring Str...
Machining and Monitoring Strategies Part 3 doc
... G.T.]
.
Machining and Monitoring Strategies
Figure 225. Variax/Hexapod oers a unique and rigid design solution, with many production benets. [Cour-
tesy of Giddings & Lewis]
.
Machining and ... allows the ‘Variax’ to move and
accelerate up to ve times faster than a conventional machine
tool.
Machining and Monitoring Strategies
Figure 226. Robotic high-...
Machining and Monitoring Strategies Part 4 docx
... 24 inches of length. is 7/24 system
incorporates several Standards: CAT and BT 40- and 50-taper
tooling.
Machining and Monitoring Strategies
e capacity for the workpiece, or even a chuck ... operations.
[Courtesy of Heartech Precision Inc. (HPI)]
.
Machining and Monitoring Strategies
quickly heats up the holder and in so doing, expands
the bore allowing the...
Machining and Monitoring Strategies Part 9 pot
... °Celsius = 5/9 (°F - 32)
(Sources: Avner, 19 74; Bofors, 19 81)
Machining and Monitoring Strategies
e term ‘ultra-precision machining – that is its
accuracy and precision, really does need to be ... dimensional sizes and scales, for:
• machining of accurate and presicion parts or
• equated to their respective measurement.
[Source: Smith, et al., 2002]
.
Machining...
Machining and Monitoring Strategies Part 10 ppsx
... [Source:
Lamb & Gull, 19 99]
.
Machining and Monitoring Strategies
Figure 255. Some typical micro-tooling: drills and boring tools.
Machining and Monitoring Strategies
sizes of 25 ... these insert’s. Other micro-machin-
Machining and Monitoring Strategies
over 1 C. e hydraulic and electronic cabinets were
temperature – controlled to ± 1 C. e...