Machinability and Surface Integrity Part 12 ppsx

Ngày tải lên: 05/08/2014, 21:20

... enter- ing the surface leading to greater thermal damage and poorer part surface integrity. e chemical mechanism is dominant across all classes of production process to some degree and that surfaces ... the component(s). Machinability and Surface Integrity  Figure 185. The cross-section of an anisotropic (i.e. periodic) surface, illustrating surface contaminants (...

Ngày tải lên: 05/08/2014, 21:20

... University. . Machinability and Surface Integrity  7 Machinability and Surface Integrity ‘It is common sense to take a method and try it. If it fails, admit it frankly and try another. ... which it appears. Machinability and Surface Integrity  Figure 144. The major factors that inuence a machined component’s condition. Machinability and Surface In...

Ngày tải lên: 05/08/2014, 21:20

... accelerated machinability test, illustrating how ank wear and surface texture degrades, with the number of facing-o passes . Machinability and Surface Integrity  tions. For a practical machinability ... Figure 149. Flow chart indicating the desigh philosophy for unbiased and ranked machinability trials. Machinability and Surface Integrity  ... utilised. O...

Ngày tải lên: 05/08/2014, 21:20

... the order to ‘break-rank’ (i.e randomising both their pacing and steps) when proceeding over a structure such as a bridge was mandatory. Machinability and Surface Integrity  is either ‘pearled’ ... of instrument noise, or vibration. [Courtesy of Taylor Hobson] . Machinability and Surface Integrity  Figure 156. Vibration and chatter in machining operations, with the...

Ngày tải lên: 05/08/2014, 21:20

... deviation of a sample from a production batch run. Machinability and Surface Integrity  depending upon whether a ne, medium, or coarse surface texture is obligatory. Due to the variability ... such surface texture values do not reect the likely in-service performance of the part. Neither the surface topography, nor its associated integrity has been quantied by assign...

Ngày tải lên: 05/08/2014, 21:20

... processes. Machinability and Surface Integrity  the surface topography, if used in conjunction with the Ra value (Fig. 164). is is particularly true for many machining applications and where ... following expression: Machinability and Surface Integrity  the point, that all of these two-dimensional surface pa- rameters can be classied into three distinct groupi...

Ngày tải lên: 05/08/2014, 21:20

... min –1 and the machinability trials used an in-cut time of just 6 seconds – in order to maintain a sharp cutting edge on the tools. Machinability and Surface Integrity  Figure 168. In face- and ... both the surface texture and its propor- tional bandwidth, with similar values with respect to its roundness. ese machinability and metrology trends’ allow examination...

Ngày tải lên: 05/08/2014, 21:20

... (isotherms) during machining, illustrated across the: chip, insert and work- piece; at relatively low cutting speed . Machinability and Surface Integrity  Figure 173. Finite Element Method (FEM), to ... – is usually the re- sult of tool/workpiece anity associated with tem- Machinability and Surface Integrity  perature and its respective cutting speed (i.e. see Fig...

Ngày tải lên: 05/08/2014, 21:20

... types of machinability investigation. In the former case, it is Machinability and Surface Integrity  Tool-life Diagrams Machinability is a subject that has yet to be fully-de- ned and analysed, ... appropriate cali- Machinability and Surface Integrity  Figure 178. Multi-axis non-rotating dynamometers, used for: milling, drilling and turning experimental data-ga...

Ngày tải lên: 05/08/2014, 21:20