Machinability and Surface Integrity Part 8 pps

... appropriate cali- Machinability and Surface Integrity  Figure 1 78. Multi-axis non-rotating dynamometers, used for: milling, drilling and turning experimental data-gathering and analysis. [Courtesy ... types of machinability investigation. In the former case, it is Machinability and Surface Integrity  Tool-life Diagrams Machinability is a subject that has yet to...

Ngày tải lên: 05/08/2014, 21:20

... the order to ‘break-rank’ (i.e randomising both their pacing and steps) when proceeding over a structure such as a bridge was mandatory. Machinability and Surface Integrity  is either ‘pearled’ ... of instrument noise, or vibration. [Courtesy of Taylor Hobson] . Machinability and Surface Integrity  Figure 156. Vibration and chatter in machining operations, with the...

Ngày tải lên: 05/08/2014, 21:20

... eect. is potential stabilising eect could be the result of energy Machinability and Surface Integrity  Figure 1 58. The eect of increased milling cutter length on the resultant circular ... deviation of a sample from a production batch run. Machinability and Surface Integrity  depending upon whether a ne, medium, or coarse surface texture is obligatory. Due to t...

Ngày tải lên: 05/08/2014, 21:20

... machining and its aect on induced residual stresses and the micro- hardness ‘foot-printing’ technique . Machinability and Surface Integrity  the Vickers 84 , or the Knoop 85 is utilised (Fig. 187 c) ... the component(s). Machinability and Surface Integrity  Figure 185 . The cross-section of an anisotropic (i.e. periodic) surface, illustrating surface contami...

Ngày tải lên: 05/08/2014, 21:20

Ngày tải lên: 05/08/2014, 21:20

... University. . Machinability and Surface Integrity  7 Machinability and Surface Integrity ‘It is common sense to take a method and try it. If it fails, admit it frankly and try another. ... which it appears. Machinability and Surface Integrity  Figure 144. The major factors that inuence a machined component’s condition. Machinability and Surface In...

Ngày tải lên: 05/08/2014, 21:20

... Figure 1 48. Graphical results obtained from the accelerated machinability test, illustrating how ank wear and surface texture degrades, with the number of facing-o passes . Machinability and Surface ... Figure 149. Flow chart indicating the desigh philosophy for unbiased and ranked machinability trials. Machinability and Surface Integrity  ... to each other (i...

Ngày tải lên: 05/08/2014, 21:20

... processes. Machinability and Surface Integrity  the surface topography, if used in conjunction with the Ra value (Fig. 164). is is particularly true for many machining applications and where ... following expression: Machinability and Surface Integrity  the point, that all of these two-dimensional surface pa- rameters can be classied into three distinct groupi...

Ngày tải lên: 05/08/2014, 21:20

... min –1 and the machinability trials used an in-cut time of just 6 seconds – in order to maintain a sharp cutting edge on the tools. Machinability and Surface Integrity  Figure 1 68. In face- and ... ‘beta-function’ and typical ‘manufacturing process envelopes’. Machinability and Surface Integrity  the considerably larger eective tool nose radius, act- ing like...

Ngày tải lên: 05/08/2014, 21:20

... 1.2 1.9 2 .8 1 .8 Ground 0.1-0.25 2-4 1.2 1.9 2 .8 1 .8 Super-nished 0.03 0.4 1.2 1.9 2 .8 1 .8 * When s/k is <0.5, an asperity is totally elastic – if the plasticity index is <5 and totally ... of tool/workpiece anity associated with tem- Machinability and Surface Integrity  perature and its respective cutting speed (i.e. see Fig. 28) . Moreover, it can also tr...

Ngày tải lên: 05/08/2014, 21:20