Modular Tooling and Tool Management Part 6 pps
Modular Tooling and Tool Management Part 6 pps
... integrated tool and data management system – for complete tooling deployment. [Courtesy of Susta – Tool Handling] . Modular Tooling and Tool Management Figure 141. Presetting equipment and ‘guidelines’ ... purchasing de- cisions on new tooling. .. Computerised -Tool Management – a Practical Case for ‘Stand-alone’ Machine Tools If one considers the tooling...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 1 ppsx
... Machines] . Modular Tooling and Tool Management 6. 1 Modular Quick-Change Tooling Introduction e modular tooling concept was developed by cut- ting tool manufacturers from the long-standing tool- ing ... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Toolin...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 2 ppsx
... it Figure 123. Modular tooling ‘capto’ with tool security and precision location via face and lobed taper contact. [Courtesy of Seco Tools] . Modular Tooling and Tool Management ... concept. Together and employing these stated design crite- ria, the following repeatability for the KM modular tooling concept was obtainable: Modular Tooling and Tool Ma...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 3 ppt
... 131. Tooling and xturing must be precisely controlled at the ‘focal-point’ of kit build-up/replenishment – at the tool preparation area. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool ... for security reasons). A typical tool le must contain all the information rel- Modular Tooling and Tool Management Figure 127. HSK high-speed modular tooling,...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 4 pdf
... competitors tooling products, • Obsolete tooling should be ‘weeded-out’ – particu- larly with the introduction and addition to the tool le of newer high-technology tooling, • Investigation of new tooling ... tool setting and tool breakage detection, utilising an ‘on-machine’ non-contact laser. [Courtesy of Renishaw plc] . Modular Tooling and Tool Management ...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 5 doc
... optical tool presetting machine. [Courtesy of E. Zoller GmbH & Co. KG] . Modular Tooling and Tool Management Figure 1 36. Optical tool presetting machine for sophisticated tool management ... mill, then it will cut Modular Tooling and Tool Management storage magazine. e latest tool presetting machines equipped with a full suite of tool management...
Ngày tải lên: 05/08/2014, 21:20
modular tooling and tool management 29 pot
... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool Management vital and helpful tooling ... taper. Modular Tooling and Tool Management Figure 1 36. Optical tool presetting machine for sophisticated tool management control. [Courtesy of E...
Ngày tải lên: 27/06/2014, 23:20
Chapter 016. Back and Neck Pain (Part 6) pps
... Neuroimaging studies reveal a low-lying conus (below L1-L2) and a short and thickened filum terminale. Chapter 0 16. Back and Neck Pain (Part 6) Congenital Anomalies of the Lumbar Spine Spondylolysis ... This is a common cause of chronic or recurrent low back and leg pain (Figs. 16- 3 and 16- 4). Disk disease is most likely to occur at the L4-L5 and L5-S1 levels, but...
Ngày tải lên: 06/07/2014, 12:20
Chapter 024. Gait and Balance Disorders (Part 6) ppsx
... people: Clinical approach and classification. Lancet Neurol 6: 63, 2007 [PMID: 17 166 803] Springer S et al: Dual-tasking effects on gait variability: The role of aging, falls, and executive function. ... improve safety, including improved lighting and the installation of grab bars and nonslip surfaces. Chapter 024. Gait and Balance Disorders (Part 6) Toppling Falls S...
Ngày tải lên: 06/07/2014, 13:20
Chapter 033. Dyspnea and Pulmonary Edema (Part 6) pps
... r eferred for cardiac stress testing. N Engl J Med 353:1889, 2005 [PMID: 162 67320] Dyspnea mechanisms, assessment, and management: A consensus statement. Am Rev Resp Crit Care Med 159:321, 1999 ... Chapter 033. Dyspnea and Pulmonary Edema (Part 6) Distinguishing Cardiogenic from Noncardiogenic Pulmonary Edema The history ... uniformly throughout the lungs, and pleural...
Ngày tải lên: 06/07/2014, 15:21