Modular Tooling and Tool Management Part 5 doc

... optical tool presetting machine. [Courtesy of E. Zoller GmbH & Co. KG] . Modular Tooling and Tool Management  Figure 136. Optical tool presetting machine for sophisticated tool management ... mill, then it will cut Modular Tooling and Tool Management  storage magazine. e latest tool presetting machines equipped with a full suite of tool management...

Ngày tải lên: 05/08/2014, 21:20

... Machines] . Modular Tooling and Tool Management  6.1 Modular Quick-Change Tooling Introduction e modular tooling concept was developed by cut- ting tool manufacturers from the long-standing tool- ing ... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling...

Ngày tải lên: 05/08/2014, 21:20

... concept. Together and employing these stated design crite- ria, the following repeatability for the KM modular tooling concept was obtainable: Modular Tooling and Tool Management  5. Tool is ready ... it Figure 123. Modular tooling ‘capto’ with tool security and precision location via face and lobed taper contact. [Courtesy of Seco Tools] . Modular Toolin...

Ngày tải lên: 05/08/2014, 21:20

... 131. Tooling and xturing must be precisely controlled at the ‘focal-point’ of kit build-up/replenishment – at the tool preparation area. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool ... for security reasons). A typical tool le must contain all the information rel- Modular Tooling and Tool Management  Figure 127. HSK high-speed modular tooling,...

Ngày tải lên: 05/08/2014, 21:20

... competitors tooling products, • Obsolete tooling should be ‘weeded-out’ – particu- larly with the introduction and addition to the tool le of newer high-technology tooling, • Investigation of new tooling ... tool setting and tool breakage detection, utilising an ‘on-machine’ non-contact laser. [Courtesy of Renishaw plc] . Modular Tooling and Tool Management ...

Ngày tải lên: 05/08/2014, 21:20

... integrated tool and data management system – for complete tooling deployment. [Courtesy of Susta – Tool Handling] . Modular Tooling and Tool Management  Figure 141. Presetting equipment and ‘guidelines’ ... purchasing de- cisions on new tooling. .. Computerised -Tool Management – a Practical Case for ‘Stand-alone’ Machine Tools If one considers the tooling...

Ngày tải lên: 05/08/2014, 21:20

... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool Management  vital and helpful tooling ... taper. Modular Tooling and Tool Management  Figure 136. Optical tool presetting machine for sophisticated tool management control. [Courtesy of E....

Ngày tải lên: 27/06/2014, 23:20

... 53 53 54 0.2030 0.1034 54 54 55 0.2842 0.1447 55 55 56 0.2813 0.1433 56 56 57 1 .59 00 0 .53 37 57 57 58 0.7837 0.2630 58 58 59 0.3042 0.1006 59 59 60 0.3861 0.1172 60 60 61 0 .50 75 0. 258 5 61 ... 8.00 5. 00 48 79.00 56 .40 14 8.00 5. 50 49 384.70 274 .50 16 45. 50 30.00 50 384.70 274 .50 17 60.00 35. 00 51 40 .50 28.30 18 60.00 35. 00 52 3.60 2.70 20 1.00...

Ngày tải lên: 19/06/2014, 10:20

... 0 25 50 75 100 1 25 150 1 75 200 0 20 40 60 80 100 120 140 160 I, µA [FA], mM Chi^2 = 2.30E-12 R^2 = 0.999 Imax 250 5. 25 μA Km 119.9 5. 34 mM (A) 02468101214 0 100 200 300 400 50 0 600 Chi^2 ... 2.32±0.08 1.97±0.12 1. 65 0. 35 1.20±0. 15 DK 6 5. 73±0.32 5. 60±0.28 4.64±0.24 4.99±0.06 DK 7 2.47±0. 15 2.19±0.2 1.62±0.17 1.96±0.20 WW-A 112±4 .5 (SAT) 84.4±6 .5 (routin...

Ngày tải lên: 20/06/2014, 05:20

... credits, and imposing upfront charges on grant recipients. Additional grant financing by donors is made up of two parts. The first is the upfront payment by donors of the foregone service and commitment ... LOW INCOME COUNTRIES: POLICY AND RESOURCE IMPLICATIONS Paper submitted for the G-24 Technical Group Meeting (Washington, D.C. September 27-28 2004) Part 5 Nihal Ka...

Ngày tải lên: 13/12/2013, 22:15