Modular Tooling and Tool Management Part 3 ppt
Modular Tooling and Tool Management Part 3 ppt
... Figure 131 . Tooling and xturing must be precisely controlled at the ‘focal-point’ of kit build-up/replenishment – at the tool preparation area. [Courtesy of Sandvik Coromant] . Modular Tooling and ... for security reasons). A typical tool le must contain all the information rel- Modular Tooling and Tool Management Figure 127. HSK high-speed modular tooling...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 1 ppsx
... Machines] . Modular Tooling and Tool Management 6.1 Modular Quick-Change Tooling Introduction e modular tooling concept was developed by cut- ting tool manufacturers from the long-standing tool- ing ... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 2 ppsx
... it Figure 1 23. Modular tooling ‘capto’ with tool security and precision location via face and lobed taper contact. [Courtesy of Seco Tools] . Modular Tooling and Tool Management ... concept. Together and employing these stated design crite- ria, the following repeatability for the KM modular tooling concept was obtainable: Modular Tooling and Tool M...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 4 pdf
... in Fig. 134 ai. Chapter Figure 133 . Cutting tool osets being set on a turning and machining centre. [Courtesy of Renishaw plc]. Modular Tooling and Tool Management block’ 31 . e Z-axis ... competitors tooling products, • Obsolete tooling should be ‘weeded-out’ – particu- larly with the introduction and addition to the tool le of newer high-technology...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 5 doc
... suppliers. Figure 137 . Typical cutter screen displays from an optical tool presetting machine. [Courtesy of E. Zoller GmbH & Co. KG] . Modular Tooling and Tool Management Figure 136 . Optical tool ... machine for sophisticated tool management control. [Courtesy of E. Zoller GmbH & Co. KG]. Modular Tooling and Tool Management Figure 138 . The correc...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 6 pps
... integrated tool and data management system – for complete tooling deployment. [Courtesy of Susta – Tool Handling] . Modular Tooling and Tool Management Figure 141. Presetting equipment and ‘guidelines’ ... Metrology and Machine Performance, Computational Mechanics Pub., 30 7 31 6, 19 93. Zoller, C. From Presetting to Tool Management. Cutting Tool Eng’g., 3...
Ngày tải lên: 05/08/2014, 21:20
modular tooling and tool management 29 pot
... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool Management vital and helpful tooling ... taper. Modular Tooling and Tool Management Figure 136 . Optical tool presetting machine for sophisticated tool management control. [Courtesy of E...
Ngày tải lên: 27/06/2014, 23:20
Energy Technology and Management Part 3 ppt
... wall I Corner I total r3 Outer 4 .32 2.59 2.51 43. 08 Inner 4 .32 2.59 1 .35 r9 Outer 3. 22 1. 03 23. 38 176.56 Inner 3. 22 1. 03 16.51 Long flat wall Short flat wall r9 Long flat wall Short flat wall r3 Fig. 11. ... (mm) Thickness of corner (mm) Density (g/cm 3 ) r3 group r3-45 45 2 2.2 2.7 2.4 1 .33 r3-18 18 3 2.8 2.6 2 .3 1.28 r9 group r9-45 45 2 2 .3 2.9 2.7 1.20 r9-18 18...
Ngày tải lên: 19/06/2014, 10:20
Waste Water Evaluation and Management Part 3 pptx
... 27.7% (3) and 7.5% (4), and 85.6 37 .39 % (3) and 19.85 3. 82% (4), respectively. Conversely, for samples 5 and 7 the respirometric assay demonstrated higher sensitivity than the standard assay ... (2) and 14 .3% (6), 14. 03 4.97% (2) and 14.54±0.74% (6), respectively. Samples 3 and 4 showed a higher sensitivity in standard assay than in respirometric assay, with EC 50 va...
Ngày tải lên: 20/06/2014, 05:20
Quality Management and Six Sigma Part 3 ppt
... 5.72 5. 13 5.29 5.46 3 5. 43 5.80 5.78 5 .39 5 .32 5.55 4 5.45 5.57 5 .32 4.68 5.44 5.29 5 5.78 5.88 5.90 4.90 5. 93 5.68 6 5.59 5.70 5.80 5.10 5.84 5.61 7 5.54 5.80 6 .34 6.20 6.04 5.99 8 5. 43 5.74 ... 5.72 5. 13 5.29 5.46 3 5. 43 5.80 5.78 5 .39 5 .32 5.55 4 5.45 5.57 5 .32 4.68 5.44 5.29 5 5.78 5.88 5.90 4.90 5. 93 5.68 6 5.59 5.70 5.80 5.10 5.84 5.61 7 5.54 5.80 6 .34...
Ngày tải lên: 20/06/2014, 11:20