Modular Tooling and Tool Management Part 2 ppsx
Modular Tooling and Tool Management Part 2 ppsx
... it Figure 123 . Modular tooling ‘capto’ with tool security and precision location via face and lobed taper contact. [Courtesy of Seco Tools] . Modular Tooling and Tool Management ... concept. Together and employing these stated design crite- ria, the following repeatability for the KM modular tooling concept was obtainable: Modular Tooling and Tool M...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 1 ppsx
... Machines] . Modular Tooling and Tool Management 6.1 Modular Quick-Change Tooling Introduction e modular tooling concept was developed by cut- ting tool manufacturers from the long-standing tool- ing ... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 3 ppt
... for security reasons). A typical tool le must contain all the information rel- Modular Tooling and Tool Management Figure 127 . HSK high-speed modular tooling, for machining applications ... 131. Tooling and xturing must be precisely controlled at the ‘focal-point’ of kit build-up/replenishment – at the tool preparation area. [Courtesy of Sandvik Coromant] . Modu...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 4 pdf
... competitors tooling products, • Obsolete tooling should be ‘weeded-out’ – particu- larly with the introduction and addition to the tool le of newer high-technology tooling, • Investigation of new tooling ... tool setting and tool breakage detection, utilising an ‘on-machine’ non-contact laser. [Courtesy of Renishaw plc] . Modular Tooling and Tool Management ...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 5 doc
... optical tool presetting machine. [Courtesy of E. Zoller GmbH & Co. KG] . Modular Tooling and Tool Management Figure 136. Optical tool presetting machine for sophisticated tool management ... mill, then it will cut Modular Tooling and Tool Management storage magazine. e latest tool presetting machines equipped with a full suite of tool management...
Ngày tải lên: 05/08/2014, 21:20
Modular Tooling and Tool Management Part 6 pps
... Figure 1 42. An integrated tool and data management system – for complete tooling deployment. [Courtesy of Susta – Tool Handling] . Modular Tooling and Tool Management Figure ... Design and Operation of FMS. IFS Pub. Ltd., 1983. Renishaw Ballbar Diagnostic Manual. Renishaw plc Pub., 20 07. Sandvik Pub. Modern Metal Cutting: Part 7 – Milling Tools. 1980. Modular...
Ngày tải lên: 05/08/2014, 21:20
modular tooling and tool management 29 pot
... employing modular quick-change tooling on a turning centre, via the ‘intelligent/ tagget’ tooling concept. [Courtesy of Sandvik Coromant] . Modular Tooling and Tool Management vital and helpful tooling ... taper. Modular Tooling and Tool Management Figure 136. Optical tool presetting machine for sophisticated tool management control. [Courtesy of E....
Ngày tải lên: 27/06/2014, 23:20
A textbook of Computer Based Numerical and Statiscal Techniques part 2 ppsx
... () 22 2 2 22 2 12 12 22 2 12 12 1 2 2 n n XX x X xx xxx xx xx x ∂∂ δ ∂ δ+δ++δ+δδ++ ∂∂ ∂∂ δ Errors δx 1 , δx 2 , , δx n all are small so that the terms containing (δx 1 ) 2 , (δx 2 ) 2 , ... δδδ δ δδ∂∂ +=×+×−=− ∂∂ 121 21 12 2 11 12 2 122 22 1 xx x xxxx XX xx Xx Xx x x xx xx Therefore δδ δ ≤+ 12 12 xx X Xx x or Relative Error ≤+ 12 12...
Ngày tải lên: 04/07/2014, 15:20
Professional ASP.NET 3.5 in C# and Visual Basic Part 2 ppsx
... ftoc.tex V2 - 01 /28 /20 08 5:00pm Page xvii Contents SessionState Providers 609 Web Event Providers 6 12 Configuration Providers 620 The WebParts Provider 623 Configuring Providers 625 Summary 626 Chapter ... Control Toolkit 929 Downloading and Installing 929 New Visual Studio Templates 931 Adding the New Controls to the VS2008 Toolbox 9 32 The ASP.NET AJAX Controls 934 ASP.NET AJAX...
Ngày tải lên: 05/07/2014, 18:20
Chapter 109. Disorders of Platelets and Vessel Wall (Part 2) ppsx
... macrothrombocytopenia. D. Schistocytes and decreased platelets in microangiopathic hemolytic anemia. Chapter 109. Disorders of Platelets and Vessel Wall (Part 2) Thrombocytopenia Thrombocytopenia ... one or more of three processes: (1) decreased bone marrow production; (2) sequestration, usually in an enlarged spleen; and/ or (3) increased platelet destruction. Disorde...
Ngày tải lên: 07/07/2014, 04:20