Handbook of Lubrication Episode 2 Part 7 potx
Handbook of Lubrication Episode 2 Part 7 potx
... Λ, the ratio of EHD film thickness to composite surface roughness,
has come into use to define the state of lubrication. Composite surface roughness, in turn,
524 CRC Handbook of Lubrication
Copyright ... Society of Mechanical Engineers, New York, 1 971 .
With permission.)
FIGURE 22 . Lubrication life adjustment factor for tapered roller bearing.
(From Danner, C. H., ASLE Tra...
Handbook of Lubrication Episode 2 Part 7 pptx
... Λ, the ratio of EHD film thickness to composite surface roughness,
has come into use to define the state of lubrication. Composite surface roughness, in turn,
524 CRC Handbook of Lubrication
Copyright ... Society of Mechanical Engineers, New York, 1 971 .
With permission.)
FIGURE 22 . Lubrication life adjustment factor for tapered roller bearing.
(From Danner, C. H., ASLE Tra...
Handbook of Lubrication Episode 2 Part 12 potx
... Society for Testing Materials, Philadelphia, 19 67, 159.
21 . Rubenstein, M., Fluid power in aerospace, Hydraul. Pneumatics, 25 (9), 20 2, 1 973 .
22 . Anon., Mold corrosion, abrasion checked with new ... protection.
636 CRC Handbook of Lubrication
Copyright © 1983 CRC Press LLC
FIGURE 2. Types of tribological systems.
Table 1
CLASSIFICATION OF TECHNICAL FUNCTIONS OF
TRIBOLOG...
Dictionary of Engineering Episode 2 Part 7 potx
... equal to
its test or during its operation. { pərfo
˙
rиməns
30 .25 square yards, or 27 2 .25 square feet, or
karиikиtərisиtik }
25 .29 28 526 4 square meters. { pərch }
performance chart
[
ENG
]
A graph ... fraction
ka
¨
ndиənsa
¯
иshən}
(around 80%) of the result. Also known as rule
particle
See material particle. { pa
¨
rdиəиkəl}
of 80 -20 . { pəre
¯
dиo
¯
z lo
˙
}
particle dy...
Handbook of Lubrication Episode 1 Part 7 pptx
... as 2. 5 GPa (3 62, 500 psi).
39
146 CRC Handbook of Lubrication
Table 1
VALUES OF C, n
1
, AND n
2
FOR EQUATION 11
a/b C n
1
n
2
5 1. 625 0 .74 – 0 .22
2 1.560 0 .73 6 – 0 .20 9
1 1.415 0. 72 5 – 0. 174
0.5 ... elastohydrodynamic
lubrication, Paper C 37/ 72 , Proc. 19 72 Syrnp. Elastohydrodynamic Lubrication, Insfitute of Mechanical
Engineers, London, 19 72 , 1 42.
57....
Handbook of Lubrication Episode 1 Part 7 ppt
... as 2. 5 GPa (3 62, 500 psi).
39
146 CRC Handbook of Lubrication
Table 1
VALUES OF C, n
1
, AND n
2
FOR EQUATION 11
a/b C n
1
n
2
5 1. 625 0 .74 – 0 .22
2 1.560 0 .73 6 – 0 .20 9
1 1.415 0. 72 5 – 0. 174
0.5 ... elastohydrodynamic lubrication of point contacts, J. Lubr.
Technol., 98 (2) , 22 3, 1 976 ; 98(3), 1 976 ; 99 (2) , 26 4, 1 977 ; 99(1), 15, 1 977 .
31. Chiu, Y....
Handbook of Lubrication Episode 1 Part 9 potx
... value of K (K =αK
m
) for unlubricated AISI- 521 00 steel is of the order of 1 ×
10
−3
.
23
For antiwear and EPadditives, K values are of the order of 10
−9
to 10
7
in four-
ball wear tests.
24
Table ... the wear rate of a copper pin
sliding against steel vs. the rate of hydrogen sulfide formation.
14
21 2CRC Handbook of Lubrication
FIGURE 3. Effect of concentrati...
Handbook of Lubrication Episode 1 Part 10 potx
... SI units is equal to 1 cm
2
/sec or
Volume II 22 9
22 7 -25 4 4/10/06 2: 07 PM Page 22 9
Copyright © 1983 CRC Press LLC
Table 5
EFFECT OF REAR AXLE LUBRICANTS ON
FATIGUE LIFE OF TAPERED ROLLER
BEARINGS
SAE ... accuracy,
24 0 CRC Handbook of Lubrication
22 7 -25 4 4/10/06 2: 07 PM Page 24 0
Copyright © 1983 CRC Press LLC
are the Cleveland Open Cup flash and fire point...
Handbook of Lubrication Episode 2 Part 1 pot
... Pittsburgh, 19 72 .
20 . Snoeys, R., The significance of chip thickness in grinding, Ann. CIRP. 23 (2) , 22 7, 1 974 .
21 . Brecker, J. N. and Shaw, M. C., Measurement of the effective number of cutting ... New Theory of Grinding, Institution of Engineers, Australia, 19 72 , 73 .
25 . Shaw, M. C. and DeSalvo, G. J., The role of elasticity in hardness testing, Metals Eng. Qu...
Handbook of Lubrication Episode 2 Part 1 pdf
... Pittsburgh, 19 72 .
20 . Snoeys, R., The significance of chip thickness in grinding, Ann. CIRP. 23 (2) , 22 7, 1 974 .
21 . Brecker, J. N. and Shaw, M. C., Measurement of the effective number of cutting ... New Theory of Grinding, Institution of Engineers, Australia, 19 72 , 73 .
25 . Shaw, M. C. and DeSalvo, G. J., The role of elasticity in hardness testing, Metals Eng. Qu...
Từ khóa: