Handbook of Lubrication Episode 2 Part 4 pps
Handbook of Lubrication Episode 2 Part 4 pps
... CRC Handbook of Lubrication From which the power loss per sector is H = 3. 04 × 2 × 10 –6 × (3 14) 2 (2. 75) 4 /0.0 02 = 1.70 × 10 4 lb in./sec (2. 58 hp) FIGURE 18. Tangential location of center -of- pressure ... /P = 1.8 × 10 –6 × 40 × (10/0. 020 ) 2 /20 0 = 0.090 Minimumfilmthickness— Entering Figure 24 with S = 0.090 and Re = 21 60: h n /C = 0 .44 h n = 0 .44 × ....
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 1 Part 4 ppsx
... characteristic equation for s is (43 ) where solutions are (44 ) Referring to Equation 42 we see that our two natural frequencies are (45 ) which are the natural frequencies of two simple, uncoupled, spring-mass ... y′satisfies the right-hand sides of Equations 47 and 48 : (49 ) (50) where: Equations 49 and 50 give the forced vibration response solution to Equations 47 and 48 a...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 2 Part 4 ppt
... elastic support 43 4 CRC Handbook of Lubrication Copyright © 1983 CRC Press LLC 42 8 CRC Handbook of Lubrication β = 40 ° (0.70 rad) γ r = 0 (no radial tilt) R 2 = 5.50 in. γ θ = 5. 82 × 10 4 rad (0.0333°) R 1 = ... calculated as W = 0.058 × 6 × 2 × 10 –6 × 3 14( 5.50 – 2. 75) 4 /0.0 02) 2 = 3 125 lb h min /h c = 0 .45 ; h min = 0 .45 × 0.0 02 = 0.00090 in. Hh c...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 2 Part 6 pps
... damage on a 44 -mm (1.15 in.) diameter aluminum bearing from a high-speed gas compressor. Figure 26 is an enlargement of the damage. Volume II493 FIGURE 24 . Enlargement of fretting corrosion of bronze ... bushing of Figure 23 . (Magnification × 15.) 1 ,2 FIGURE 25 . Cavitation erosion of a 44 -mm (1.75- in.) diameter aluminum bearing. 1 ,2 Copyright © 1983 CRC Press LLC Vol...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 2 Part 6 pps
... II493 FIGURE 24 . Enlargement of fretting corrosion of bronze bushing of Figure 23 . (Magnification × 15.) 1 ,2 FIGURE 25 . Cavitation erosion of a 44 -mm (1.75- in.) diameter aluminum bearing. 1 ,2 Copyright ... potential between the extremities of the shaft. Using this method on ordinary electrical apparatus with 48 4CRC Handbook of Lubrication FIGURE 12. Principal so...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 2 Part 2 pps
... Leeuwenhoek J., 26 , 22 5, I960. 43 . Hill, E. C., Biodeterioration of Metal Working Fluids and Its Significance, Publ. No. MR 72- 2 14, American Society of Mechanical Engineers, New York, 19 72. 1. 44 . Hill, ... Bacterial., 24 , 125 , 1961. 46 . Bennett, E. O., The Effect of Water Hardness on the Deterioration of Cutting Fluids, Tech. Pap. No. MR 72- 226 , Society of Mechani...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 1 Part 1 ppsx
... Volume 2) Main entry under title: CRC Handbook of Lubrication (Tribology) Tiile of v, 2 varies: CRC handbook of lubrication (theory and practice of tribology) Bibliography: v. 1. p.: v. 2, p. Includes ... Standard Book Number 0- 849 3-39 02- 2 (Volume II) Library of Congress Card Number 82- 45 52 Printed in the United States of America 15 16 17 18 19 20 Printed on...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 1 Part 4 doc
... R. Soc. London Ser. A, 22 3, 28 9, 1 923 . 4. Vohr, J. H., An experimental study of Taylor vortices and turbulence in flow between eccentric rotating cyclinders, Trans. ASME Ser. F, 90, 28 5, 1968. 5. DiPrima, ... characteristic equation for s is (43 ) where solutions are (44 ) Referring to Equation 42 we see that our two natural frequencies are (45 ) which are the natural frequenci...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 2 Part 1 pot
... Pittsburgh, 19 72. 20 . Snoeys, R., The significance of chip thickness in grinding, Ann. CIRP. 23 (2) , 22 7, 19 74. 21 . Brecker, J. N. and Shaw, M. C., Measurement of the effective number of cutting points ... dressing. In such cases, the G = volume of work removed volume of work consumed 3 52 CRC Handbook of Lubrication 335-356 4/ 11/06 12: 34 PM Page 3 52 Copyrigh...
Ngày tải lên: 05/08/2014, 09:20
Handbook of Lubrication Episode 2 Part 1 pdf
... of work removed volume of work consumed 3 52 CRC Handbook of Lubrication 335-356 4/ 11/06 12: 34 PM Page 3 52 Copyright © 1983 CRC Press LLC Copyright © 1983 CRC Press LLC 12. Tipnb, V. A. and Joseph, ... Univ., April 19 72, in New Developments in Grinding, Carnegie Press, Pittsburgh, 19 72. 20 . Snoeys, R., The significance of chip thickness in grinding, Ann. CIRP. 23 (2)...
Ngày tải lên: 05/08/2014, 09:20