Handbook of Lubrication Episode 1 Part 14 doc

... surface. 335-356 4 /11 /06 12 :33 PM Page 337 Copyright © 19 83 CRC Press LLC (Figure 10 a) (11 ) (Figure 10 b) (12 ) As already mentioned slip does not occur on every atomic plane but only on bands of planes in ... Figure 11 . In this case the inclination angle is the helix angle of the cutting edge. 344 CRC Handbook of Lubrication Table 2 REPRESENTATIVE VALUES 335-356 4 /11 /...

Ngày tải lên: 05/08/2014, 09:20

... II 329 317 -333 4 /10 /06 12 :59 PM Page 329 Copyright © 19 83 CRC Press LLC (Figure 10 a) (11 ) (Figure 10 b) (12 ) As already mentioned slip does not occur on every atomic plane but only on bands of planes ... Figure 11 . In this case the inclination angle is the helix angle of the cutting edge. 344 CRC Handbook of Lubrication Table 2 REPRESENTATIVE VALUES 335-356 4 /11 /06...

Ngày tải lên: 05/08/2014, 09:20

... H. J., On the critical contact temperature of lubricated sliding- rolling disks. ASLE Trans., 21, 16 1, 19 78. 68 CRC Handbook of Lubrication Copyright © 19 83 CRC Press LLC Short Journal Bearing The ... Boundary lubrication, Lubrication, 57, 1, 19 71. 4. Niemann, G., Rettig, H., and Lechner, G., Scuffing tests on gear oils in FZG apparatus, ASLE Trans., 4, 71, 19 61. Volume...

Ngày tải lên: 05/08/2014, 09:20

... FORTRAN statements. 12 ,13 13 2 CRC Handbook of Lubrication 12 1 -13 7 4 /11 /06 12 :28 PM Page 13 2 Copyright © 19 83 CRC Press LLC vector or scalar quantities plotted over the clearance space of all possible ... ratio < 1. (Recall that previous dimensionless quantities for planar bearings were constants.) Thus, ∋ 12 6 CRC Handbook of Lubrication 12 1 -13 7 4 /11 /0...

Ngày tải lên: 05/08/2014, 09:20

... Resistance Results of many tests of the resistance of materials to abrasive wear using abrasive paper Volume II 17 1 16 3 -18 4 4 /10 /06 12 :36 PM Page 17 1 Copyright © 19 83 CRC Press LLC WEAR OF NONMETALLIC ... operation. 16 3 -18 4 4 /10 /06 12 :37 PM Page 18 1 Copyright © 19 83 CRC Press LLC Table 3 HARDNESS OFABRASIVES 41 MaterialHardness (MNm –2 ) Glass5790 Quartz103...

Ngày tải lên: 05/08/2014, 09:20

... Lubr.Technol., 10 0, 12 9, 19 78. 35. Onions, R. A. and Archard, J. F., Pitting of gears and discs, Proc. Inst. Mech. Eng., 18 8, 673, 19 74. Volume II 18 3 16 3 -18 4 4 /10 /06 12 :37 PM Page 18 3 Copyright © 19 83 ... K. A. R., An investigation of fretting corrosion, Proc. Inst. Mech. Eng., 1B, 556, 19 52. 18 4 CRC Handbook of Lubrication 16 3 -18 4 4 /10 /06 12 :37...

Ngày tải lên: 05/08/2014, 09:20

... MPa 1/ 2 Helium0. 012 3.35 Neon0. 018 3.87 Hydrogen0.0405.52 Nitrogen0.0696.04 Air0.0986.69 Carbon monoxide0 .12 7.47 Oxygen0 .16 7.75 Argon0 .18 7.77 Methane0. 319 .10 Krypton0.6 010 .34 Carbon dioxide1.4 514 . 81 Ammonia1.7 Ethylene ... lubrication of graphite, ASLE Trans., 10 , 10 , 19 67. 5. Rowe, C. N., Role of additive adsorption in the mitigation of wear, ASLE Trans., 1...

Ngày tải lên: 05/08/2014, 09:20

... numbersMinMax 21. 982.42 32.883.52 54 .14 5.06 76 .12 7.48 10 9.0 011 .0 15 13. 516 .5 2 219 .824.2 3228.835.2 46 41. 450.6 68 61. 274.8 10 090. 011 0 15 013 516 5 22 019 8242 320288252 460 414 506 680 612 748 1, 00090 01, 100 1, 50 01, 35 01, 650 original ... (orig.) ~280 NA ~220 NA DEHS (HMW) 277 7 .19 219 13 .69 MLO 7558 (HMW) 278 11 .65 225 17 .62 MLO 7 219 (HMW) 275 48.47 223...

Ngày tải lên: 05/08/2014, 09:20

... principal component of air: the viscosity is 18 10 –6 Pa·sec up to 40 atm pressure, 20 10 –6 at 10 0 bar, and 53 10 –6 at 10 00 bar. The viscosities of airat several pressures from 1 to 10 0 bar are ... lubricant, ASLE Trans., 13 , 56, 19 70. 14 . Play, D. and Godet, M., Study of the Lubricating Properties of (CF x ) n , Coll. Int. CNRS, 233, 4 41, 19 75; NASA Rep. TM 7...

Ngày tải lên: 05/08/2014, 09:20

... especially crankcase motor oils. 21. Polyisobutylene 314 CRC Handbook of Lubrication 3 01- 315 4 /10 /06 12 : 51 PM Page 314 Copyright © 19 83 CRC Press LLC FIGURE 6. Geometry of roll pass and associated ... Liquid Lubricant Technology, NASA SP- 318 , NTIS N74 -12 219 -12 230, Ku, P. M., Ed., 19 73, 433. Volume II 315 3 01- 315 4 /10 /06 12 : 51 PM Page 315 Copyright ©...

Ngày tải lên: 05/08/2014, 09:20