Geometric Dimensioning and Tolerancing for Mechanical Design Part 14 docx
Geometric Dimensioning and Tolerancing for Mechanical Design Part 14 docx
... Characteristic Symbols, 18 Geometric controls to refine datum features, 229, 232, 235 Geometric Dimensioning and Tolerancing, 2 Geometric form, 69 Graphic analysis, 207 Immobilization of a part, 48 Implied ... 55 Fixed and double fixed fasteners, 128 Fixed fastener formula, 129 Flatness, 69 Unit flatness, 71 253 Copyright © 2006 by Gene R. Cogorno. Click here for terms of use. 2...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 14 pot
... sketch (cartoon gage), 236 Geometric Characteristic Symbols, 18 Geometric controls to refine datum features, 229, 232, 235 Geometric Dimensioning and Tolerancing, 2 Geometric form, 69 Graphic analysis, ... positional tolerancing, 135 Composite profile, 195 Conical taper, 28 Controlled radius symbol (CR), 28 Coordinate conversion diagram, 251 Coordinate conversion table, 252 Coordi...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 doc
... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... 10.1036/00 7146 0705 GeometricDimensioning andTolerancingfor MechanicalDesign x Preface To optimize the learning process an to drive the information into long-term memory, rev...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 pps
... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... April 8, 2006 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimensioning and toleranc...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 potx
... to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Chapter 2 Dimensioning and Tolerancing Fundamentals Many people know how to design parts and ... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Dimension...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 pps
... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 16 Chapter Two 5. A applies where centerlines and lines representing ... either in degrees and decimal parts of a degree or in degrees, minutes, and seconds. There are two types of direct tolerancing methods, limit dimensioning...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 3 doc
... Dimension is a numerical value without a tolerance, used only for general information. It is additional information and may not be used for manufacturing or inspection. The reference dimension is ... government standards and are not controlled by Rule #1. Stock is used as is, unless otherwise specified by a geometric tolerance or note. Rule #1 does not apply to parts that are flexible...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 4 ppsx
... dimensioning a part. Figure 4-4 shows a part with four holes. The designer selected the back of the part as the primary datum, datum A, because the back of the part mates with another part, and the ... Part Parts are thought to have six degrees of freedom, three degrees of translational freedom, and three degrees of rotational freedom. A part can move back and forth in the...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pptx
... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April 10, 2006 20:8 1.500 w ... thickness of 1.010 for the rectangular part and a diameter of 1.010 for the cylindrical part. Since the MMC of 1.020 minus the actual size of 1.010 is the automatic Ru...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pdf
... as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-05 MHBD031-Cogorno-v6.cls April 11, 2006 20:17 Form 85 w Figure 5-15 Straightness ... control the form of a feature, a form tolerance may be specified as a refinement. Except for straightness of a median line and of a median plane, all form tolerances are surface cont...
Ngày tải lên: 05/08/2014, 09:20