Geometric Dimensioning and Tolerancing for Mechanical Design Part 13 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 13 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 13 pps

... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 235 flat on the outside diameter has been designated as datum C and specified as ... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 233 8X Ø .500 540 Figure 14-10 A zero po...

Ngày tải lên: 05/08/2014, 09:20

20 307 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 pps

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... April 8, 2006 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimensioning and toleranc...

Ngày tải lên: 05/08/2014, 09:20

20 449 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 pps

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 16 Chapter Two 5. A applies where centerlines and lines representing ... either in degrees and decimal parts of a degree or in degrees, minutes, and seconds.  There are two types of direct tolerancing methods, limit dimensioning...

Ngày tải lên: 05/08/2014, 09:20

20 421 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 4 ppsx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 4 ppsx

... dimensioning a part. Figure 4-4 shows a part with four holes. The designer selected the back of the part as the primary datum, datum A, because the back of the part mates with another part, and the ... Part Parts are thought to have six degrees of freedom, three degrees of translational freedom, and three degrees of rotational freedom. A part can move back and forth in the...

Ngày tải lên: 05/08/2014, 09:20

20 457 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 9 ppsx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 9 ppsx

... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU Chapter08 MHBD031-Cogorno-v6.cls April 18, 2006 15:10 C .50 1.00 A .50 Unless ... head in a countersunk hole and in a threaded hole at the other end is called what? 6. The formula for fixed fasteners is 7. The tolerance for both the threa...

Ngày tải lên: 05/08/2014, 09:20

20 363 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 10 ppsx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 10 ppsx

... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-10 MHBD031-Cogorno-v5.cls April 11, 2006 23:3 Concentricity and Symmetry 173  The concentricity ... Concentricity is appropriately used for large, expensive parts that must have a small coax- ial tolerance for balance but need not have the same small tolerance for...

Ngày tải lên: 05/08/2014, 09:20

20 484 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 11 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 11 pps

... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-12 MHBD031-Cogorno-v6.cls April 18, 2006 0:20 Profile ... sheet metal part in Fig. 12- 22 coplanar within .020. Tolerance holes with geometric tolerancing. The smallest size tolerance for each hole is the virtual condition for...

Ngày tải lên: 05/08/2014, 09:20

20 353 1
Geometric Dimensioning and Tolerancing for Mechanical Design Part 11 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 11 pps

... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-12 MHBD031-Cogorno-v6.cls April 18, 2006 0:20 190 ... sheet metal part in Fig. 12- 22 coplanar within .020. Tolerance holes with geometric tolerancing. The smallest size tolerance for each hole is the virtual condition for the...

Ngày tải lên: 05/08/2014, 09:20

20 265 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 13 potx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 13 potx

... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 235 flat on the outside diameter has been designated as datum C and specified as ... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 233 8X Ø .500 540 Figure 14-10 A zero po...

Ngày tải lên: 05/08/2014, 09:20

20 313 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 doc

Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 doc

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... sector, geometric dimensioning and tolerancing (GD&T) is a new subject. During World War II, the United States manufactured and shipped spare parts overseas for...

Ngày tải lên: 05/08/2014, 09:20

20 499 0
w