Geometric Dimensioning and Tolerancing for Mechanical Design Part 13 potx

... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 235 flat on the outside diameter has been designated as datum C and specified as ... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 233 8X Ø .500 540 Figure 14-10 A zero po...

Ngày tải lên: 05/08/2014, 09:20

... to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Chapter 2 Dimensioning and Tolerancing Fundamentals Many people know how to design parts and ... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Dimension...

Ngày tải lên: 05/08/2014, 09:20

... tolerance zone for a through hole, place a circle P in the feature control frame after the material condition symbol, and specify both maximum height and direction by drawing and dimensioning a ... The chain line is the MMC height of the mating part and located on the side where the mating part assembles. If the mating part is 1.500 ± .030 thick and assembles on top of the...

Ngày tải lên: 05/08/2014, 09:20

... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 235 flat on the outside diameter has been designated as datum C and specified as ... Strategy for Tolerancing Parts P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 A Strategy for Tolerancing Parts 233 8X Ø .500 540 Figure 14-10 A zero po...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... sector, geometric dimensioning and tolerancing (GD&T) is a new subject. During World War II, the United States manufactured and shipped spare parts overseas for...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... April 8, 2006 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimensioning and toleranc...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 16 Chapter Two 5. A applies where centerlines and lines representing ... either in degrees and decimal parts of a degree or in degrees, minutes, and seconds.  There are two types of direct tolerancing methods, limit dimensioning...

Ngày tải lên: 05/08/2014, 09:20

... Dimension is a numerical value without a tolerance, used only for general information. It is additional information and may not be used for manufacturing or inspection. The reference dimension is ... government standards and are not controlled by Rule #1. Stock is used as is, unless otherwise specified by a geometric tolerance or note. Rule #1 does not apply to parts that are flexible...

Ngày tải lên: 05/08/2014, 09:20

... dimensioning a part. Figure 4-4 shows a part with four holes. The designer selected the back of the part as the primary datum, datum A, because the back of the part mates with another part, and the ... Part Parts are thought to have six degrees of freedom, three degrees of translational freedom, and three degrees of rotational freedom. A part can move back and forth in the...

Ngày tải lên: 05/08/2014, 09:20

... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April 10, 2006 20:8 1.500 w ... than the size tolerance. The parts in Fig. 5-4 are likely to be produced at a thickness of 1.010 for the rectangular part and a diameter of 1.010 for the cylindrical p...

Ngày tải lên: 05/08/2014, 09:20