Geometric Dimensioning and Tolerancing for Mechanical Design Part 12 pptx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 12 pptx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 12 pptx

... a part. Some designers believe that parts designed with a solid modeling CAD program do not require tolerancing. A note in the Dimen- sioning and Tolerancing standard indicates caution when designing ... 2006 21:50 Chapter 14 A Strategy for Tolerancing Parts When tolerancing a part, the designer must determine the attributes of each feature or pattern of features and the relati...

Ngày tải lên: 05/08/2014, 09:20

20 281 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pptx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pptx

... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April 10, 2006 20:8 1.500 w ... than the size tolerance. The parts in Fig. 5-4 are likely to be produced at a thickness of 1.010 for the rectangular part and a diameter of 1.010 for the cylindrical p...

Ngày tải lên: 05/08/2014, 09:20

20 362 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 12 pot

Geometric Dimensioning and Tolerancing for Mechanical Design Part 12 pot

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-14 MHBD031-Cogorno-v6.cls April 11, 2006 21:50 Chapter 14 A Strategy for Tolerancing Parts When tolerancing a part, ... a part. Some designers believe that parts designed with a solid modeling CAD program do not require tolerancing. A note in the Dimen- sioning and Toleranc...

Ngày tải lên: 05/08/2014, 09:20

20 308 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 doc

Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 doc

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... sector, geometric dimensioning and tolerancing (GD&T) is a new subject. During World War II, the United States manufactured and shipped spare parts overseas for...

Ngày tải lên: 05/08/2014, 09:20

20 499 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 pps

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... April 8, 2006 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimensioning and toleranc...

Ngày tải lên: 05/08/2014, 09:20

20 449 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 potx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 potx

... to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Chapter 2 Dimensioning and Tolerancing Fundamentals Many people know how to design parts and ... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Dimension...

Ngày tải lên: 05/08/2014, 09:20

20 518 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 pps

Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 pps

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 16 Chapter Two 5. A applies where centerlines and lines representing ... either in degrees and decimal parts of a degree or in degrees, minutes, and seconds.  There are two types of direct tolerancing methods, limit dimensioning...

Ngày tải lên: 05/08/2014, 09:20

20 421 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 3 doc

Geometric Dimensioning and Tolerancing for Mechanical Design Part 3 doc

... Dimension is a numerical value without a tolerance, used only for general information. It is additional information and may not be used for manufacturing or inspection. The reference dimension is ... government standards and are not controlled by Rule #1. Stock is used as is, unless otherwise specified by a geometric tolerance or note. Rule #1 does not apply to parts that are flexible...

Ngày tải lên: 05/08/2014, 09:20

20 396 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 4 ppsx

Geometric Dimensioning and Tolerancing for Mechanical Design Part 4 ppsx

... dimensioning a part. Figure 4-4 shows a part with four holes. The designer selected the back of the part as the primary datum, datum A, because the back of the part mates with another part, and the ... Part Parts are thought to have six degrees of freedom, three degrees of translational freedom, and three degrees of rotational freedom. A part can move back and forth in the...

Ngày tải lên: 05/08/2014, 09:20

20 457 0
Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pdf

Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pdf

... as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-05 MHBD031-Cogorno-v6.cls April 11, 2006 20:17 Form 85 w Figure 5-15 Straightness ... control the form of a feature, a form tolerance may be specified as a refinement. Except for straightness of a median line and of a median plane, all form tolerances are surface cont...

Ngày tải lên: 05/08/2014, 09:20

20 436 0
w