Geometric Dimensioning and Tolerancing for Mechanical Design Part 7 ppt
Geometric Dimensioning and Tolerancing for Mechanical Design Part 7 ppt
... n\w.004m\A\B\C] Figure 7- 17 Boundary conditions: Problem 3. 3. First calculate the virtual and resultant conditions for the pin and the hole. Then calculate the maximum and minimum distances for dimensions X and ... subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031- 07 MHBD0...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pptx
... the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April 10, 2006 20:8 1.500 w 1.000- 1.030 4X .76 0 79 0 2.500 1.500 3.000 3.500 ... given at the website. Form P1: PBU MHBD031-05 MHBD031-Cogorno-v6.cls April 11, 2006 20: 17 Form 77 tolerance (Rule #1) and must be less than the size tolerance, exce...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 6 ppt
... use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design ... specified correctly in order to communicate design intent. The feature control frame in Fig. 7- 1 tells the location tolerancing story for the hole in this part: it has a cylindrical tolerance zone ... parts will always assemble, datums A...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 6 ppt
... Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-06 MHBD031-Cogorno-v5.cls April 11, 2006 17: 55 92 Chapter Six Figure 6-6 Verifying ... used of the 14 geometric characteristics. The position tolerance significantly contributes to part function, part interchangeability, optimization of tolerance, and commu-...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 7 doc
... n\w.004m\A\B\C] Figure 7- 17 Boundary conditions: Problem 3. 3. First calculate the virtual and resultant conditions for the pin and the hole. Then calculate the maximum and minimum distances for dimensions X and ... subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031- 07 MHBD0...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 8 ppt
... symbol, and specify both maximum height and direction by drawing and dimensioning a thick chain line next to an extension of the centerline. The chain line is the MMC height of the mating part and ... drill chart and a chart of oversize diameters in drilling are located in the appendix of this text. TABLE 8-1 Drill Chart Letter Fraction Decimal 17/ 64 .266 H – .266 I – . 272 J...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 12 pptx
... a part. Some designers believe that parts designed with a solid modeling CAD program do not require tolerancing. A note in the Dimen- sioning and Tolerancing standard indicates caution when designing ... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-13 MHBD031-Cogorno-v6.cls April 11, 2006 17: 1 222 Chapter Thirteen A 4 B D...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 doc
... Review 173 Problems 175 Chapter 11. Runout 177 Chapter Objectives 177 Definition 177 Circular Runout 177 Total Runout 178 Specifying Runout and Partial Runout 179 Multiple Datum Features 179 ... 10.1036/0 071 46 070 5 GeometricDimensioning andTolerancingfor MechanicalDesign x Preface To optimize the learning process an to drive the information into long-term memory, review all new...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 pps
... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... MHBD031-Cogorno-v6.cls April 8, 2006 17: 58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimen...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 potx
... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Dimensioning and Tolerancing Fundamentals 11 44 .72 ° 25° 10' ... to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Chapter 2 Dimensioning and Tolerancing Fundamen...
Ngày tải lên: 05/08/2014, 09:20