Geometric Dimensioning and Tolerancing for Mechanical Design Part 7 doc

... n\w.004m\A\B\C] Figure 7- 17 Boundary conditions: Problem 3. 3. First calculate the virtual and resultant conditions for the pin and the hole. Then calculate the maximum and minimum distances for dimensions X and ... subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031- 07 MHBD0...

Ngày tải lên: 05/08/2014, 09:20

... Review 173 Problems 175 Chapter 11. Runout 177 Chapter Objectives 177 Definition 177 Circular Runout 177 Total Runout 178 Specifying Runout and Partial Runout 179 Multiple Datum Features 179 ... 10.1036/0 071 46 070 5 GeometricDimensioning andTolerancingfor MechanicalDesign x Preface To optimize the learning process an to drive the information into long-term memory, review all new...

Ngày tải lên: 05/08/2014, 09:20

... reference specified for gears and splines must designate the specific feature at which each applies such as . 47. Where a datum feature of size is controlled by a geometric tolerance and is specified ... government standards and are not controlled by Rule #1. Stock is used as is, unless otherwise specified by a geometric tolerance or note. Rule #1 does not apply to parts that are flex...

Ngày tải lên: 05/08/2014, 09:20

... n\w.004m\A\B\C] Figure 7- 17 Boundary conditions: Problem 3. 3. First calculate the virtual and resultant conditions for the pin and the hole. Then calculate the maximum and minimum distances for dimensions X and ... subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031- 07 MHBD0...

Ngày tải lên: 05/08/2014, 09:20

... .189 #8 .1640 .2 87 .226 #10 .1900 .334 .262 1/4 .2500 .443 .346 5/16 .3125 .5 57 .434 3/8 . 375 0 . 670 .522 7/ 16 .4 375 .70 7 . 572 1/2 .5000 .76 6 .633 5/8 .6250 .944 .78 4 3/4 .75 00 1.185 .9 67 ∗ Clearance ... .218 . 178 #8 .1640 .262 .213 #10 .1900 .303 .246 1/4 .2500 .365 .3 07 5/16 .3125 .4 57 .384 3/8 . 375 0 .550 .462 7/ 16 .4 375 .642 .540 1/2 .5000 .73 5 .6 17 5/8 6250...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dimensioning and Tolerancing 1 Chapter ... MHBD031-Cogorno-v6.cls April 8, 2006 17: 58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimen...

Ngày tải lên: 05/08/2014, 09:20

... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Dimensioning and Tolerancing Fundamentals 11 44 .72 ° 25° 10' ... to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 Chapter 2 Dimensioning and Tolerancing Fundamen...

Ngày tải lên: 05/08/2014, 09:20

... website. Dimensioning and Tolerancing Fundamentals P1: PBU introduction1 MHBD031-Cogorno-v6.cls April 8, 2006 17: 58 Introduction to Geometric Dimensioning and Tolerancing 7 2X Ø .510 530 1.00 .75 2.50 Unless ... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 2006 18:6 16 Chapte...

Ngày tải lên: 05/08/2014, 09:20

... dimensioning a part. Figure 4-4 shows a part with four holes. The designer selected the back of the part as the primary datum, datum A, because the back of the part mates with another part, and the ... Part Parts are thought to have six degrees of freedom, three degrees of translational freedom, and three degrees of rotational freedom. A part can move back and forth in the...

Ngày tải lên: 05/08/2014, 09:20

... the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April 10, 2006 20:8 1.500 w 1.000- 1.030 4X .76 0 79 0 2.500 1.500 3.000 3.500 ... given at the website. Form P1: PBU MHBD031-05 MHBD031-Cogorno-v6.cls April 11, 2006 20: 17 Form 77 tolerance (Rule #1) and must be less than the size tolerance, exce...

Ngày tải lên: 05/08/2014, 09:20